A thin aluminumplate profile shown in the accompanying figure is subjected to an axial load. Approximate the deflection and the average normal stresses along the plate using 2 cm 2 cm the model shown in the 2 сm figure. The plate has a thickness of 0.5cm and a 3000 N modulus of elasticity E=70 6 ст 6 сm GPa. 10 cm

A thin aluminumplate profile shown in the accompanying figure is subjected to an axial load. Approximate the deflection and the average normal stresses along the plate using 2 cm 2 cm the model shown in the 2 сm figure. The plate has a thickness of 0.5cm and a 3000 N modulus of elasticity E=70 6 ст 6 сm GPa. 10 cm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.11.2P: A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30...

See similar textbooks

Similar questions

A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
A mountain bike rider going uphill applies a force P = 65 N to each end of the handlebars AB CD, made of aluminum alloy 7075-T6, by pulling on the handlebar extenders (DF on right handlebar segment). Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A), Segments AB and CD are prismatic with lengths Lvand L3 and with outer diameters and thicknesses J01, /01 and d03, /03, respectively, as shown. Segment BC of length L2, however, is tapered, and outer diameter and thickness vary linearly between dimensions at B and C Consider shear, torsion, and bending effects only for segment AD; assume DFis rigid. Find the maximum tensile, compressive, and shear stresses adjacent to support A. Show where each maximum stress value occurs
A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30 kN and A = 60 kN (see figure) The bar is constructed of magnesium alloy having a stress-strain curve described by the Ram berg-Osgood equation: 45.000 618 UW id which u has units of mega pascals (MPa). (a) Calculate the displacement 8t- of the end of the bar when the load P:acts alone. (b) Calculate the displacement when the load P, acts alone. (c) Calculate the displacement when both loads act simultaneously.
– The weight is suspended from structural A–36 steel alloy and 2014-T6 aluminum alloy wires, eachhaving the same initial length of 10 ft and cross-sectional area of 7×10–3 in2 (Figure Q1). If the weight is increasedgradually, determine which wire yields first? Explain which material model and yield criterion you will use? Justifyyour choices
The part shown is formed from a 1/8 - in diameter steel wire, with R = 2.5 in and l = 2 in. A force is applied withP = 1 lbf. Use Castigliano's method to estimate the horizontal deflection at point A. Justify any components ofstrain energy that you choose to neglect.
Please help me for the correct solution. A leaf spring carries a central load of 3000 N. The leaf spring has to be made of 10 steel plates 5cm wide and 6mm thick. If the bending stress is limited to 150 N/mm² determine: (i) Length of the spring and (ii) Deflection at the centre of the spring. Take E = 2 * 10 ^ 5 * N / m * m ^ 2..?
In the figure shown, the deflection of mercury is initially 250mm. If the pressure at a is increased by 40kPa, while maintaining the pressure at b constant, what will be the new mercury deflection?
a machine mass m = 500 kg is mounted on a simply supported steel beam of length l = 2 that has a rectangular cross section (thickness = 0.1 m and width 1.2 m) and whose young modulus is given by E = 2.06x10 ^ 11 N / m2. To reduce the vertical deflection of the beam, a spring of stiffness k is added in the middle of the span, as shown in the following figure. Determine the value of k necessary to reduce the deflection of the beam by: a) -25% of its original valueb) -50% of its original valuec) -75% of its original value
need help calculating displecment / deflection using formula: W*L3 / 48*E*I W: 0,5,10,15,20,25 (N) L3: 0.4m E: Modulus of elasticity of Aluminum I: moment of Inertia: 1.51 x 10^-9 The cross section of material is aluminum tube 12.7mm x 9.5mm
A central horizontal section of a hook is a symmetrical trapezium of inner width=67.5mm and of outer width =22.5mm. The depth of the section is 90mm. The hookcarries a load of 37.5kN. The load line passes through the centre of curvature. Theradius of the hook is 52.5mm. Determine the maximum compressive and tensilestresses in the section of the hook.
A semi-elliptical spring 800mm long has eight leaves, two of which are full length. Theleaves are 8mm thick and 60mm wide each. It is desired to replace this spring by a helicalcoil spring of 100mm mean diameter and of such nature that for any load it will have thesame induced stress and same deflection as the leaf spring. What should be the diameter ofthe wire?