QUESTION 3) Closed and open triangular section tubes are made of same materials are shown in figure. If the both cross-sections yield at equal allowable stress value; determine the Mk and Ma torsional moments ratio Mk/MA . (t=0.1 cm and a=5 cm) 4a За

QUESTION 3) Closed and open triangular section tubes are made of same materials are shown in figure. If the both cross-sections yield at equal allowable stress value; determine the Mk and Ma torsional moments ratio Mk/MA . (t=0.1 cm and a=5 cm) 4a За

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.3P: A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b...

See similar textbooks

Related questions

Q: Q16/ The value of the normal stress due to :axial force 2 kN applied on the beam is Point D 10 kN…

A: For this question, Axial force = P = 2 kN = 2000 N Cross section of the beam = 200 mm x 100 mm We…

Q: The shaft shown in the figure left has the diameters 304 Stainless steel - 2014-T6 Aluminum and…

Q: The steel propeller shaft ABCD carries the axial loads shown in Figure. Determine the change in the…

A: Answer: The change in length of the shaft is 0.0136 in.

Q: Q1) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length…

A: Given dataLoad P = 2700radius of the filled r = 5Diameter D = 62.5d = 50dH= 6.25To determine the…

Q: Calculate the maximum shear stresses from the torsional moment it the shaft between the points B and…

Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m

A: Find the stresses at point C.

Q: Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze 83…

Q: A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside…

A: Given data Power transmitted = 45 kW Speed (N) = 500 rpm Inside dia (d) = 0.6*outside dia(D)…

Q: In figure below, the shear force (Q) is equal to 150 kN. What is the shear stress (t) at the neutral…

Q: I. Problem Solving. Box your final answer. 1. Find the (a) maximum tensile and compressive bending…

Q: Q) In Fig.(1), the shaft is subjected to a reversed load P (2700 to -900) N. Find the length (L), if…

Q: A hollow tubular shaft will be used between the engine and the propeller of the boat as shown in the…

A: given data;outer diameter (do)=74mmthickness (t)=6mmengine power(P)=10KWspeed (n)=694rpmstress on…

Q: 1. In figure below, the lower member is of uniform cross section and can be assumed to be rigid.…

A: Given;

Q: Determine the torsional stress of the cantilever shafts show in the figure below: C 200 5 KN.m T 15…

Q: he cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the…

A: Givenm=15σcb=6N/mm2σst=120N/mm2

Q: Determine the maximum tensile and compressive stresses developed in the overhanging beam that is…

Q: 25 kips 20 in.- Figure 1 10 in. 25 kips 20 in. B 7.25 in. Sin.- b 1.5 in. 1.5 in.

Q: On the surface of a structural member, stresses are given as ox=67,9 MPa, oy=25,5 MPa and Ty=-24,3…

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: Determine the maximum shear stress in the shaft (Figure 1). Given the torsional shear stress is 45…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Determine the maximum tensile stress of the beam with details shown in Figure 2.

Q: 6. Refer to figure 2. Bar АВCD with cross-sectional FIGURE 2 area equal to 600 mm?. Determine the…

Q: 20 KN it 80 Q3/ A bracket is supported using 4 rivets having same size, as shown in Figure 3.…

Q: List down the formulas for calculating the shear stress and angle of twist of the following cross…

A: It is asked to write the shear stress and angle of twist formula for the cross-sections of shape…

Q: 4.) A 12 watts DC motor is used to run a remote-controlled car. A 3-inch aluminum shaft, with a…

A: Answer: (a) The maximum shear stress in the shaft is 3.65 MPa. (b) The angle of twist at the free…

Q: QUESTION I The beam in the figure below is made from three boards nailed together as shown. If the…

Q: Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure…

Q: QUESTION 1 A Z-section beam of 2 m long and is supported as a cantilever with a 1 kN load at the…

Q: Q15. The rigid bar is supported by steel rods (E - 200,000 MPa) (AB, CD and EF) and hinge as shown…

Q: Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze 83…

A: Given data Area of Steel section = As = 300 mm2Area of Aluminum section = Aal = 600 mm2Area of…

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

Q: The beam with its section, given in the figure; a) Calculate the value of the location of the…

Q: PROBLEM 3. The beam shown in the figure is made of steel with oai=300 MPa. Determine the maximum…

Q: Q2 Determine the maximum tensile stress of the beam with details shown in Figure 2. 48 kN 60 kN 60…

Q: 5. Find 2 in 口2 im 300 lb-ft cosS - Section V80 lb it =33.9 psi Tonia Ob -b =8.48 psi TL-b= 147 Psi…

A: Let us consider tension force in inclined member is P. Drawing FBD of horizontal member:

Q: QUESTION 1) A channel type cross-section is subjected to the compression force P-20 kN at the point…

A: The section is as shown below, The area of the section is, A1=20×5=100 cm2A2=20×5=100…

Q: Problem (4.7): For the thin-wall tubular sections shown in Figure (4.28); (a) Determine the maximum…

Q: Determine the total stress at point A on the cross section a-a in the figure below. 400 kN la -0.5…

A: Draw a diagram showing the neutral axis for the above-cross section.

Q: QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum…

A: Cross-sectional view,

Q: The steel propeller shaft ABCD carries the axial loads shown in the figure. Determine the change in…

A: The forces are shown in each member below: The internal forces in 3 segments are :- PAB = PBC…

Q: Determine the torsional stress of the cantilever shafts show in the figure below: 200 5 KN.m 150…

A: To find : Torsional stress of the cantilever shaft Given : inside diameter di=15mm outside…

Q: Determine the minimum allowable diameter of the circular shaft to the nearest millimeter if the…

Q: The cross-section of the beam is rectangular everywhere, and the size of the cross-section is given…

A: Given width of beam w=50mmhieght of the beam h=100mm

Q: Q#2: Explain the absolute maximum shear stress. Construct Tresca's hexagon by explaining all the…

A: Given data To explain the absolute maximum shear stress and construct by Tresca’s hexagon by…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPª لاخرين 24 1 10 2 20 МРа…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: Question 3: An unknown amount of vertical shear force (not shown in the figure) is applied to the…

Q: TL My 10 cm 600 N 14 cm B Vertical load is applied to point B of a 10 mm radius cylindrical bar as…

A: r= 10 mmso D=20 mmFrom figure 600×14 N-cm causes to twist the bar and 600×10 N-cm at D causes normal…

Q: The circular shaft is subjected to cyclic load. The Shaft is subjected to maximum load of 500 kN and…

Q: The beam shown in the figure is made of steel with oal=300 MPa. Determine the maximum load, P, that…

A: According to the given information, we have a beam which is shown in the figure, the stress in steel…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?
Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure. The rack is made up of 2 in. x 2 in. steel tubing which is 1/8 in. thick. Assume that the weight of each of four bicycles is distributed evenly between the two support arms so that the rack can be represented as a cantilever beam (ABCDEF) in the xy plane. The overall weight of the rack alone is W = 60 lb directed through C, and the weight of each bicycle is P = 30 lb.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A standpipe in a water-supply system (see figure) is 12 ft in diameter and 6 in. thick. Two horizontal pipes carry water out of the standpipe; each is 2 ft in diameter and 1 in. thick. When the system is shut down and water fills the pipes but is not moving, the hoop stress at the bottom of the standpipe is 130 psi, (a) What is the height h of the water in the standpipe? (b) If the bottoms of the pipes are at the same elevation as the bottom of the stand pipe. what is the hoop stress in the pipes?
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).