In the figure shown, determine the normal stresses at AD+ and BC• , shearing stress atbolt Dbearing stress of AD at bolt D• , bearing stress of member EDC at bolt DAll bolts Ø16m0,25D20KNB.E10 x 50 mm8 × 36 mm

Solution: The free body diagram of the EDC is shown above, we need to find the reactions RD and RC…

In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • , bearing stress of AD at bolt D + , bearing stress of member EDC at bolt D All bolts Ø16m 04 n 0,25 D 20kN E 10 x 50 mm 8 x 36 mm

In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • , bearing stress of AD at bolt D + , bearing stress of member EDC at bolt D All bolts Ø16m 04 n 0,25 D 20kN E 10 x 50 mm 8 x 36 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.1P: A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer...

See similar textbooks

Related questions

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: The solid shaft is fixed in the wall at A (Figure Q2). A force F is applied at B, determine a) the…

Q: A compound shaft consists of segment (1), which has a diameter of 1.25 in., and segment (2), which…

A: Given data: A compound shaft segment (1) has a diameter of 1.25 in. A compound shaft segment (2) has…

Q: Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading…

A: It is assumed that Compressive stress developed in the top section. Also tensile stress in the…

Q: 150 B D C St Al 50 30 300 N.m 600 500

A: Applied torque, T=300 N-m Diameter of the aluminum section, dAl=50 mm Diameter of the steel section,…

Q: The stepped circular shaft made of aluminum (E = 69 Gpa, u = 0.35) is loaded by an axial force of 3…

A: Given: E=69 GPa P=3kN μ=0.35 d=12 mm D=15 mm r=2.4 mm

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 6 MРа A 6 MPa The stresses…

Q: 1. A steel thick-walled cylinder has an inner diameter of 25mm and an outer diameter 110mm. The…

Q: Due to the applied loading, the element at point A on the solid shaft in Figure is subjected to the…

A: σx=-12 ksiσy=0 ksiTxy=-6ksi σavg=σx+σy2=-6ksi R=(12-6)2+62=8.49 ksi

Q: 1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of…

A: you have posted multiple questions. As per the guidelines I am able to answer one question only. So…

Q: P=70 MPa . Determine maximum principal stress

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: Q2. A mild steel shaft transmits 'P' kW at 'N' r.p.m. It carries a central load of 900 N and is…

A: Shaft is a rotating element that transmit power and rotation.

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1850…

A: GIVEN :- b1=85mmb2=130mmb3=60mmd=28mmP=1850N

Q: Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and…

A: Given:σx=60 MPaσy=-18 MPaζxy=15 MPa

Q: 5 mm B. ON A 1900 N 800 M

A: given:

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Now we have the moment equation asMx=16×510-11×230=5630kN.mm=5.63kN.mMy=-20×510=-10200 kN.mm=-10.2…

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D bearing…

A: Given data, Diameter of the bolt, d = 16 mm Free body diagram of EDC where, RD and RC are the…

Q: Draw Mohr's circle that describes each of the following states of stress shown in Figure 5. 3 ksi 6…

A: given state of stress for element shown in figure a = -12 ksi = - 3 ksi = 0 state of…

Q: 5.0 in. 3.0 in. The 1.4-kip load P is supported by two wooden members of uniform cross section that…

A: Given load P=1.4 kip Cross section A=5×3 in.2

Q: The material used for section CB of the shaft shown has an allowable shear stress of Tallow= 75 MPa.…

A: Data given -

Q: At a point in plane stress the principal stresses were found to be 22 MPa(T) and 14 MPa (C). The…

A: The given data are: σ1=22 MPaσ2=14 MPa Here, σ1 denotes the maximum principal stress and σ2 denotes…

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given, Force, F=178NInside diameter, di=2.66cmOutside diameter,do=3.34cm Moment of Inertia,…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: A steel pipe with an outside diameter of 3 in. and an inside diameter of 2.56 in. supports the…

Q: A circular rod of a diameter of 100 mm is subjected at its free end to force F1 = 50N and F2=(200j -…

A: In this question, three forces are given. The forces are Point force, F1=50i kN Point force,…

Q: Q5: - Draw the Mohr's Circle of the stress element 6 MPa shown in figure. Find: - A 6 MPa The…

Q: Q4-A vertical force of 178 Nis applied to a pipe wrench whose handleis vertical to the z-axis as…

A: Given Data Force applied on the wrench and the force transferred to the end of the pipe, F=178 N…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: Given data: P=9 kipsQ=4 kipsR=18 kipsS=21 kipsσ1=19 ksiσ2=24 ksiσ3=12 ksi Need to determine the…

Q: A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an…

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear…

A: Given data Direct tensile stress = 300 MPa Shear stress = 200 Mpa

Q: Forces of Px = 580 lb and Py = 220 lb act on the teeth of the gear shown in Figure 1. The gear has a…

A: Given:Px=580 lbPy=220 lbRg=6 inr=2 ina=5 in

Q: 60 N- m Since each of the shafts 144 N - m , AB, BC and CD shown in the figure consists of a solid…

A: The torsional moment applied on the shaft AB is, TAB=48 N·m The diameter of the shaft AB is, dAB=15…

Q: In the following structure if the temperature increases by 20 °C, determine the normal stress in…

A: Given Data The increased temperature is: T=20°C The distance BD is: BD=400 mm The distance BF is:…

Q: 6. A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the…

A: Answer: The diameter of the shaft is 50 mm.

Q: Column is manufactured using concrete (E=4.2×10^3 ksi) and reinforcement is done by A-36 steel rods…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Given: Px=20 kNPy=16 kNPZ=11 kNdo=115 mmdi=105 mma =510 mmb= 230 mm

Q: The concrete post (Ec= 3.6 x 106 psi and ac= 5.5 x 10-6/F) is reinforced with six steel bars, each…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

A: For the Given system P = 9 kips Q = 5 kips R = 20 kips S = 30 kips stress limit in (1) = 19 ksi…

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0…

A: Solution:

Q: From the figure shown, the diameter of each segment is indicated. Determine the average normal…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: 90 MPa PROBLEM 7.15 30 MPa For the given state of stress, determine the normal and shearing stresses…

Q: A helicopter's rotor shaft has the hollow circular cross section shown as follows. The shaft is…

A: Calculated principal stress and absolute maximum shear stress at point p.

Q: 6. The figure below shows the geometry and loading of segment of a crankshaft. The diameter of the…

Q: The frame supports the triangular distributed load shown. Determine the normal and shear stresses at…

A: Reaction force acting ay point B is RB=900×32×3×13×13=450 N The cross section area is…

Q: A hollow structural steel flexural member is subjected to loads of P = 9 kips, Q = 35 kips, and R =…

A: Given: The eccentric load given: P = 9 kips The direct load, Q = 35 kips The shear force, R = 22…

Q: 3. A long thin walled cylindrical shell, closed at both the ends, is subjected to an internal…

A: Let us consider, Diameter of cylindrical shell = d Thickness of cylindrical shell = t Pressure…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

In the figure shown, determine the normal stresses at AD
+ and BC
• , shearing stress at
bolt D
bearing stress of AD at bolt D
• , bearing stress of member EDC at bolt D
All bolts Ø16m
0,25
D
20KN
B.
E
10 x 50 mm
8 × 36 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
• - 7.4-7 An element on the surface of a drive shaft is in pure shear and is subjected to stresses ??xy= 2700 psi, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an element oriented at a counterclockwise angle ?= 52° from the y axis. (b) The principal stresses. Show all results on sketches of properly oriented elements.