A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress analysis on a mechanical system. The given values of strain has been obtained. E = 121x1- E2 = 304x10- E3 = 203x10-6 Material properties of the solid body are, E = 207 Gpa and v = 0.29. For this case, calculate normal and shear stress values which occurs on the body.

A strain gage rosette has been placed on a solid member as shown in in the figure to perform stress analysis on a mechanical system. The given values of strain has been obtained. E = 121x1- E2 = 304x10- E3 = 203x10-6 Material properties of the solid body are, E = 207 Gpa and v = 0.29. For this case, calculate normal and shear stress values which occurs on the body.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.5.4P: An element of a material is subjected to plane stresses as shown in the figure. The stresses o,...

See similar textbooks

Similar questions

A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
Solve the preceding problem if the plate is made of aluminum with E = 72 GPa and Poisson’s ratio v = 0.33. The plate is loaded in biaxial stress with normal stress sx= 79 MPa, angle Ø = 18°, and the strain measured by the gage is e = 925 × 10-6.
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
1 A rectangular steel plate with thickness t = 5/8 in. is subjected to uniform normal stresses a and ., as shown in the figure. Strain gages A and B. oriented in the x and v directions. respectively, arc attached to the plate. The gage readings give normal strains = 0.00065 (elongation) and £. = 0.00040 (elongation). Knowing that E = 30 X 106 psi and v = 0.3, determine the stresses c7 and a, and the change .11 in the thickness of the plate.
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
An element of a material is subjected to plane stresses as shown in the figure. The stresses o, cry., and are 10 MPa, —15 MPa, and 5 MPa. respectively. Assume E = 200 GPa and v = 0.3. (a) Calculate the normal strain in the x, v. and z directions and the shear strain. (b) Calculate the strain-energy density of the element.
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.