A thin uniform rod of mass M and length L is nailed to the tabletop in an experiment on rotation. If the rod is nailed at a distance of (1/3)L from one of its ends and then allowed to rotate, what is the moment of inertia of the rod about this pivot point? Note that a thin uniform rod has moment of inertia Icom = ML about the center of mass (com). O (1/9) ML2 O (1/8) ML2 O (1/4) ML2 O (4/9) ML2

A thin uniform rod of mass M and length L is nailed to the tabletop in an experiment on rotation. If the rod is nailed at a distance of (1/3)L from one of its ends and then allowed to rotate, what is the moment of inertia of the rod about this pivot point? Note that a thin uniform rod has moment of inertia Icom = ML about the center of mass (com). O (1/9) ML2 O (1/8) ML2 O (1/4) ML2 O (4/9) ML2

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 103P: A uniform rod of length L and mass M is held vertically with one end resting on the floor as shown...

See similar textbooks

Similar questions

A solid cylinder of mass 2.0 kg and radius 20 cm is rotating counterclockwise around a vertical axis through its center at 600 rev/min. A second solid cylinder of the same mass and radius is rotating clockwise around the same vertical axis at 900 rev/min. If the cylinders couple so that they rotate about the same vertical axis, what is the angular velocity of the combination?
The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4 kg and its radius is 30 cm, as well as the distance from the center of mass to the pivot, what is the rotation rate in rev/s of the disk?
If the angular acceleration of a rigid body is zero, what is the functional form of the angular velocity?
A thin rod of length 2.65 m and mass 13.7 kg is rotated at anangular speed of 3.89 rad/s around an axis perpendicular to therod and through one of its ends. Find the magnitude of the rodsangular momentum.
A wheel 2.00 m in diameter lies in a vertical plane and rotates about its central axis with a constant angular acceleration of 4.00 rad/s2. The wheel starts at rest at t = 0, and the radius vector of a certain point P on the rim makes an angle of 57.3 with the horizontal at this time. At t = 2.00 s, find (a) the angular speed of the wheel and, for point P, (b) the tangential speed, (c) the total acceleration, and (d) the angular position.
Which of the entries in Table 10.2 applies to finding the moment of inertia (a) of a long, straight sewer pipe rotating about its axis of symmetry? (b) Of an embroidery hoop rotating about an axis through its center and perpendicular to its plane? (c) Of a uniform door turning on its hinges? (d) Of a coin turning about an axis through its center and perpendicular to its faces?
A uniform rod of length b stands vertically upright on a rough floor and then tips over. What is the rods angular velocity when it hits the floor?
A thin rod of length 2.65 m and mass 13.7 kg is rotated at anangular speed of 3.89 rad/s around an axis perpendicular to therod and through its center of mass. Find the magnitude of therods angular momentum.
Why is the moment of inertia of a hoop that has a mass M and a radius R greater than the moment of inertia of a disk that has the same mass and radius?
Using the parallel axis theorem, what is the moment of inertia of the rod of mass m about the axis shown below?
The position vector of a particle of mass 2.00 kg as a function of time is given by r=(6.00i+5.00tj), where r is in meters and t is in seconds. Determine the angular momentum of the particle about the origin as a function of time.
What three factors affect the torque created by a force relative to a specific pivot point?