A titration process is done by using 0.2M of 20 ml of third analytical group main reagent solution with 0.1 M nitric acid solution if nitric acid is replaced by sulphuric acid of same concentration, then the volume of sulphuric acid equals...... a. Half the volume of nitric acid b. Double the volume of nitric acid The volume of nitric acid C.

A titration process is done by using 0.2M of 20 ml of third analytical group main reagent solution with 0.1 M nitric acid solution if nitric acid is replaced by sulphuric acid of same concentration, then the volume of sulphuric acid equals...... a. Half the volume of nitric acid b. Double the volume of nitric acid The volume of nitric acid C.

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter9: Acids, Bases, And Salts

Section: Chapter Questions

Problem 9.103E

See similar textbooks

Similar questions

A monoprotic organic acid that has a molar mass of 176.1 g/mol is synthesized. Unfortunately, the acid produced is not completely pure. In addition, it is not soluble in water. A chemist weighs a 1.8451-g sample of the impure acid and adds it to 100.0 mL of 0.1050 M NaOH. The acid is soluble in the NaOH solution and reacts to consume most of the NaOH. The amount of excess NaOH is determined by titration: It takes 3.28 mL of 0.0970 M HCl to neutralize the excess NaOH. What is the purity of the original acid, in percent?
It is desired to neutralize a solution X that contains a mixture of potassium chloride and hydriodic acid. Titration of 11.0 mL X with 0.143 M silver nitrate required 39.2 mL of the latter. The resulting precipitate, containing a mixture of AgCl and AgI, was dried and found to weigh 1.190 g. How much 0.147 M sodium hydroxide should be used to neutralize 11.0 mL solution X?
A solid sample of Zn1OH22 is added to 0.350 L of 0.500 Maqueous HBr. The solution that remains is still acidic. It isthen titrated with 0.500 M NaOH solution, and it takes 88.5mL of the NaOH solution to reach the equivalence point.What mass of Zn1OH22 was added to the HBr solution?
A 5.30 mLmL sample of an H3PO4H3PO4 solution of unknown concentration is titrated with a 1.050×10−2 MNaOHMNaOH solution. A volume of 7.32 mLmL of the NaOHNaOH solution was required to reach the equivalence point. What is the concentration of the unknown H3PO4H3PO4 solution? Express your answer with the appropriate units. Value___? Units____?
In an acid-base titration experiment, a student first standardize NaOH (39.997 g/mol) with 0.7102 g of KHP (204.22 g/mol) and required 32.01 mL of the NaOH titrant solution to reach endpoint. After standardization, 0.1530 g of unknown monoprotic acid was titrated using the standardized NaOH solution and required 12.36 mL to reach the endpoint. 1.) What is the standardized concentration of titrant (in M)? 2.) What is the molar mass of the unknown monoprotic acid?
A solution containing a mixture of metal cations was treated with dilute HClHCl and a precipitate formed. The solution was filtered, and H2SH2S was bubbled through the acidic solution. A precipitate again formed and was filtered off. Then, the pH was raised to about 88 and H2SH2S was again bubbled through the solution. This time, no precipitate formed. Finally, the solution was treated with a sodium carbonate solution, which resulted in the formation of a precipitate. Classify the metal ions based on whether they were definitely present, definitely absent, or whether it was possible they were present in the original mixture.
The following solutions are needed to be prepared for the titration procedure:1. 20 mL of 2 M HCl2. 20 mL of 0.05 M KOH1.0867 grams of Fe(OH)n was mixed with the 20mL of 2 M HCl that is initially prepared. This solution was diluted to 200 mL and was labeled as solution A. 20.0 mL aliquot of solutionA was taken and titrated with 20.0 mL of 0.05 M KOH. From this data, determine for the value of n.
A student was performing this experiment with an antacid tablet which contained C a CO3 but forgot to heat the antacid solution prior to starting the back-titration. As sodium hydroxide was added the student noticed the formation of an insoluble white precipitate. Would the presence of this precipitate cause the students experimentally determined volume of N a O H be incorrectly high or incorrectly low? Briefly explain. Hint: Carbon dioxide reacts with water to form carbonic acid. Question 3 options: Incorrectly high, the solution becomes more acidic if not boiled gently Incorrectly high, the solution becomes less acidic if not boiled gently Incorrectly low, the solution becomes more acidic if not boiled gently Incorrectly low, the solution becomes less acidic if not boiled gently
During the titration of an HClO4 solution with 0.10320 M NaOH, a student, Lovely became distracted and overshot the endpoint. A fellow student Ashley suggested that he should record the present volume of NaOH added and titrate the excess with a standard acid solution. If the original sample volume was 25.000 mL, the volume of NaOH added was 28.060 mL. It took 3.4700 mL of 0.10940 M HCl to back-titrate the NaOH and calculate the molar concentration of the original HClO4
A stainless steel alloy is to be analyzed for its chromium content. A 3.30 g sample of the steel is used to produce 250.0 mL of a solution containing Cr2O72−. A 10.0-mL portion of this solution is added to BaCl2(aq). When the pH of the solution is properly adjusted, 0.145 g BaCrO4(s) precipitates. A.) What is the percent Cr, by mass, in the steel sample? Express your answer numerically as a percentage.