A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and Cz is shown in Fig. Power is transmitted from pulley A to B. The shaft is made of plain carbon steel 45C8 (S = 600 and Sy 380 N/mm?). The pulleys are keyed to the shaft. Determine the shaft diameter using the ASME code if,

A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and Cz is shown in Fig. Power is transmitted from pulley A to B. The shaft is made of plain carbon steel 45C8 (S = 600 and Sy 380 N/mm?). The pulleys are keyed to the shaft. Determine the shaft diameter using the ASME code if,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A transmission shaft, supporting two pulleys A and B and mounted between two bearings C1 and C2 is shown in Fig. Power is transmitted from pulley A to B. The shaft is made of plain carbon steel 45C8 (Sut = 600 and Syt = 380 N/mm2). The pulleys are keyed to the shaft. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0
A solid shaft transmits 1.7 kW of power at 4.4 Hz. What is the smallest safe diameter of the shaft if the shear stress is not to exceed 36 MPa?
The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm2 and yield strength of 580 N/mm2. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0 Assume that the pulley is keyed to the shaft.
The shaft and the flange of a marine engine are to be designed for flange coupling, in which the flange is forged on the end of the shaft. The following particulars are to be considered in the design: Power of the engine=2.4 MW Speed of the engine 80 r.p.m Permissible shear stress in bolts and shaft = 60 MPa Number of bolts used =6 Pitch circle diameter of bolts=1.6* Dimeter of shaft Find 1.diameter of shaft; 2.diameter of bolts; 3.thickness of flange; and 4.diameter of flange. (25 degrea
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shownin Fig. 14.19 has ratio of belt tensions 4.The gear forces are as follows :Ft = 1590 N; Fr = 580 NFig. 14.19Design the shaft diameter by maximum shear stress theory. The shaft material has the followingproperties :Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.[Ans. 20 mm
A flange coupling connects two 2” diameter shafts. The flanges are fitted with 6 bolts of SAE 1040 steel on a 7” bolt circle. The shafts runs at 300 rpm and transmits 45 hp. Assume a factor of safety of 5, ultimate tension of 70,000 psi, and ultimate shear of 55,000 psi. Determine: a) The torque transmitted, in-lbs b) The force applied per bolt, lbs c) The diameter of the bolt required, in d) The thickness of flanged to be used, in
Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be: a. 160 mm b. 74 mm C. 145 mm d. 92.5 mm e. 60 mm f. 66 mm
A hollow shaft is to transmit 350 kW at 65 rpm. If the shear stress is not to exceed 40 MPa and the diameter ratio is 0.54, Design the shaft by assuming the maximum torque is 40% greater than its mean torque. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNIT GIVEN IN BRACKET) (i) The mean torque is (Unit is in Nm)=__________ Answer for part 1 (ii) The maximum torque is (Unit is in Nm)=__________ Answer for part 2 (iii) The outer diameter of the shaft (unit in mm)=_______________ Answer for part 3 (iv) The inner diameter of the shaft (unit in mm)=_______________
Data:P = 2 kipd = 3.6 inchw = 305 millimeterst = 0.03 meterr = 5.08 centimeterh = 0.6667 feet a) Calculate the maximum static stress in the material (in MPa). b) Estimate the theoretical stress concentration factor at the fillet c) Estimate the theoretical stress concentration factor at the hole
Verify if my answers are correct: P =1000 N Q =1300 N C =216000 N.mm
What is the stress concentration factor for a shaft with a hardened profile keyway under torsion if the notch sensitivity factor is 0.67? Express your answer using 4 gnificant figures.
A belt is to transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at 1200 rpm, while the larger sheave turns at 500 rpm. Determine the design HP if a service factor of 1.35 and a correction factor of 0.85.