A solid steel shaft with a diameter of 130 mm must be press-ftted in a journal bearing (Figure 1) with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing nlet diameter as the basic size. Ouden Seing Inle Jeunal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance imits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.

A solid steel shaft with a diameter of 130 mm must be press-ftted in a journal bearing (Figure 1) with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing nlet diameter as the basic size. Ouden Seing Inle Jeunal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance imits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?
Calculate the basic rating life at 90% reliability for the following cylindrical roller bearing and conditions.Fr 5.05 kNFa 3.12 kNBearing: NU 1010 ECP (on pp 522 in the SKF catalogue)Clearance: Normal Give the answer in millions of revolutions.
A rotating shaft of 40×4 mm AISI 1018 cold-drawn steel tubing has a 6 mm diameter hole drilled transversely through it. Estimate the factor of safety guarding against fatigue and static failures using the Gerber and Langer failure criteria for the following loading conditions: a. The shaft is subjected to a completely reversed torque of 120 N.m in phase with a completely reversed bending moment of 150 N.m. b. The shaft is subjected to a pulsating torque fluctuating from 20 to 160 N.m and as steady bending moment of 150 N.m.
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
engineering tolerance: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journalbearing require rigidity and alignment with an accuracy of the location. Consider a journal bearinginlet diameter as the basic size. determine 1. the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter2. the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter
Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be: a. 160 mm b. 74 mm C. 145 mm d. 92.5 mm e. 60 mm f. 66 mm
Thory of machine: Select one of the following bearing for the load conditions. Radial load, F=3000 N, Axial load, F = 1600 N, RPM = 1000. (1) Deep Groove ball bearing dynamic load rating=47000 N radial bad factor, X=0.56 Axial load factor, Y= 1.83 (i) Cylindrical roller bearing Dynamic load rating 28000 N radial load factor, X=1.0 axial load factor, Y=0.0
A shaft which rotates at a constant speed of 160 rpm is connected by belting to a parallel shaft 750 mm apart, which has to run at 60, 80 and 100 rpm. The smallest pulley on the driving shaft is 40 mm in radius. Determine the remaining radii, the angle of contact, and the length of the belt of the two stepped pulleys for a) crossed belt, and b) an open belt. Consider a slip of 2% at each drive.
A coupling must transmit 30 hp at a speed of 175 r/min. 3/8 inch diameter bolts are arranged in a single 6 inch diameter circle. The shear stress in the bolts should not exceed 5,000 psi. What is the minimum number of bolts that should be used? Answer: seven bolts
It has a full-slide type bearing rotating at a speed of 1975 rpm.A load of 5693 N is applied. SAE 40 oil in bearing at 60C inlet temperatureplanned to be used.Shaft and bushing diameters in bearing with tolerance data 41−0.010 respectively+0.000mmand 41.125−0.000+0.100 mm.Average radial clearance mounting for this bearing with bush length 20.50 mmCalculate the following;a) Bearing characteristic number,b) Minimum lubricant film thickness,c) Eccentricity value,d) coefficient of friction,e) Average oil film temperature andf) Find the Tmax temperature value.
A hollow shaft is to transmit 350 kW at 65 rpm. If the shear stress is not to exceed 40 MPa and the diameter ratio is 0.54, Design the shaft by assuming the maximum torque is 40% greater than its mean torque. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNIT GIVEN IN BRACKET) (i) The mean torque is (Unit is in Nm)=__________ Answer for part 1 (ii) The maximum torque is (Unit is in Nm)=__________ Answer for part 2 (iii) The outer diameter of the shaft (unit in mm)=_______________ Answer for part 3 (iv) The inner diameter of the shaft (unit in mm)=_______________
A Self-aligning medium series bearing for bores of 85 mm is operating at 300 r.p.m for an average life of 9 years at 10 hours per day, is acted by a 15 kN radial load and 10 kN thrust load. The bearing is subjected to a light shock load and the inner ring is sationary. Determine the suitable self-aligning bearing. Mention the advantage of using self align bearing.