A twin engine (two engines) commercial aircraft (Fig. 1b) flies straight and level maintaining constant direction due north and producing 120KN of total thrust. Suddenly right engines fail. In this case to maintain the same direction pilot deflects the rudder to maintain the direction of the flight. Determine the force required from the rudder to maintain the direction of the flight. The tail arm It = 19.6m, the distance between engines is %3D 9.0m. North CG Fig. 1b

A twin engine (two engines) commercial aircraft (Fig. 1b) flies straight and level maintaining constant direction due north and producing 120KN of total thrust. Suddenly right engines fail. In this case to maintain the same direction pilot deflects the rudder to maintain the direction of the flight. Determine the force required from the rudder to maintain the direction of the flight. The tail arm It = 19.6m, the distance between engines is %3D 9.0m. North CG Fig. 1b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in Fig. 14.2 when the propeller is operated at an angular speed of 1400 rpm and an advance velocity of zero? Assume p = 1.05 kg m3.
Consider the system shown below. The incline plane is fixed and the coefficient kinetic friction between M and 2M is ?1, and coefficient kinetic friction between the plane and 2M is ?2. Let M=2.0kg, ?=22o, ?1=0.14, and ?2=0.25. (a) What is the magnitude of the frictional force on mass M? (b) What is the magnitude of the total frictional force on mass 2M? (c) What is the acceleration of mass M? (d) What is the acceleration of mass 2M?
A prototype jet-powered UAV has a wing planform with S = 60 ft2 and b = 20 ft. and an Oswald efficiency of e = 0.82. The aircraft has CD,0= 0.04. The weight is 2,000 lb. For this aircraft, determine the following: a. Minimum thrust required at sea level for steady level flight. b. Velocity of minimum thrust required for the conditions in (a). c. The induced drag for the conditions in (a). d. If Vmax at sea level is 550 fps, what is the thrust available in lb? e. Given the thrust available is produced by a single turbojet engine with a cross-sectional inlet area of Ain= 2.5 ft2, determine the exit velocity from the engine and the propulsion efficiency assuming the exit pressure is atmospheric..
A Boeing 777-200 commercial jet weighs, fully loaded, 325,000 kg. The pilot places the turbines in maximum power condition for takeoff (before releasing the aircraft's brakes), situation in which they generate 450 kN of thrust in each turbine. Neglecting aerodynamic and bearing, estimate runway length and time necessary to achieve the speed of takeoff of 225 km / h. consider constant thrust in the two turbines during the journey on the ground.
What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in the figure shown in the image below when the propeller is operated at an angular speed of 1400 rpm and an advance velocity of zero? Assume p = 1.05 kg m3.
In a modified version of the cart and bucket, the angle of the slope is alpha = 34.9∘ and the bucket weighs 295 N. The cart moves up the incline and the bucket moves downward, both at constant speed. The cable has negligible mass, and there is no friction. What is the weight of the cart?What is the tension in the cable?
In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
1. A wheel tractor has a 200 HP engine. Calculate the available rimpull of this tractorif it is operating at an altitude of 1,000 m. above sea level, at an averagetemperature of 25oC, and at an average speed of 12 km/hr. Take rimpull efficiencyas 85%.2. The weight of the wheel tractor in Problem 1 is 30 tons and the weight on the drivingwheels is 50% of this weight. What is the maximum available rimpull if thecoefficient of traction is 0.25?3. What is the maximum grade that the tractor in Problems 1 and 2 can climb if it ismoving on a surface with a rolling resistance of 150 kg/ton?4. Assume that the tractor in Problems 1, 2, and 3 is moving down a 8% grade. Howmany minutes are necessary to accelerate to the average speed of 5 km/hr in firstgear? Use a rimpull reduction factor of 75% in your calculations.
Blocks A, B, and C are placed as in Fig. and connected by ropes of negligible mass. Both A and B weigh 25.0 N each, and the coefficient of kinetic friction between each block and the surface is 0.35. Block C descends with constant velocity. (a) Draw separate free-body diagrams showing the forces acting on A and on B. (b) Find the tension in the rope connecting blocks A and B. (c) What is the weight of block C? (d) If the rope connecting A and B were cut, what would be the acceleration of C?
A pile-driver hammer has a mass of 300 kg and is to be raised 16 m in 4 sec. The total friction on the guides is constant at 400 N. What constant pull must be exerted on the cable?
The angle of the slope 23.0∘ and use a different cart and a different bucket. You observe that the cart and bucket remain at rest when released and that the tension in the cable of negligible mass is 175 N. There is no friction. What is the weight of the cart? What is the combined weight of the cart and bucket?
A man pulls up box of mass 70kg using an inclined plane of effective length 5m onto a platform 2.5m high at uniform speed. If the frictional force between the box and the plan is 100N draw the diagram of all the forces acting on the box when in motion and calculate the (a) minimum effort applied in pulling up the box (b) velocity ratio of the plane (c) machanical advantage of the plane