EXAMPLE: 27 9. The jet aircraft has a total mass of 22 Mg and a center of mass at G. Initially at take-off the engines provide a thrust 27 = 4kN and T' = 1.5kN. Determine the acceleration of the plane and the normal reactions on the nose 1.2m 2.5 m 2.3 m B 3 m- 6 m DEW wheel and each of the two wing wheels located at B. Neglect the mass of the wheels and, due to low velocity, neglect any lift caused by the wings.

EXAMPLE: 27 9. The jet aircraft has a total mass of 22 Mg and a center of mass at G. Initially at take-off the engines provide a thrust 27 = 4kN and T' = 1.5kN. Determine the acceleration of the plane and the normal reactions on the nose 1.2m 2.5 m 2.3 m B 3 m- 6 m DEW wheel and each of the two wing wheels located at B. Neglect the mass of the wheels and, due to low velocity, neglect any lift caused by the wings.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To avoid the bulky tower and impeller and generator inthe HAWT of the chapter-opener photo, we could insteadbuild a number of Darrieus turbines of height 4 m anddiameter 3 m. (a) How many of these would we need tomatch the HAWT’s 100 kW output for 15 m/s wind speedand maximum power? (b) How fast would they rotate?Assume the area swept out by a Darrieus turbine is twothirdsthe height times the diameter.
A static thrust stands as it showed in the Figure. The intake velocity is 200 m/s, exhaust velocity is 500 m/s, intake cross-section area 1 m, intake pressure is -22.5 kPa, and exhaust pressure is pressure and considered zero. Determine the anchoring force (Fth).( Density = 1.02kg / (m ^ 3))
The jet engine on a test stand, shown in the figure, admitsair at 20oC and 1 atm at section 1, where the area is 0.5 m2and the velocity is 250 m/s. The fuel-to-air ratio is 1:30.The air leaves at section 2 at atmospheric pressure and ahigher temperature. The exit velocity is 900 m/s and thearea is 0.4 m2. Compute the horizontal test stand reactionRx needed to hold the engine fixed.
A supply tank at 500 kPa and 400 K feeds air to a converging–diverging nozzle whose throat area is 9 cm2. The exit areais 46 cm2. State the conditions in the nozzle if the pressureoutside the exit plane is (a) 400 kPa, (b) 120 kPa, and (c) 9kPa. (d ) In each of these cases, fi nd the mass fl ow.
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.
A Pelton wheel is supplied with 12 kg/s of water at 20 m/s. The buckets rotate on amean diameter of 250 mm at 800 rev/min. The deflection angle is 165o and friction is negligible. Determine the diagrampower.The output torque of the turbine is 26.5 Nm.The pressure drop over the nozzles is 2.45 bar gauge. Assume the water densityis 1000 kg/m3 . Calculate:1. Mechanical efficiency.2. Hydraulic efficiency3. Overall efficiency
Fast pls solve this question correctly in 5 min pls I will give u like for sure Rafe Air is contained in an insulated rigid column at 20 degree Celsius and 200 kPA. A paddle wheel inserted in the volume, does 720 kJ of work on the air. If the volume is 2 m^3, calculate the entropy increase assuming constant specific heat.
A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.
Consider the fire extinguisher Assuming a steady exhaust from a 1”-diameter nozzle in the fire extinguisher, with an exhaust product density of 2.5 kg/m3, calculate the exhaust product velocity required to drain 1 kg of mass from the fire extinguisher in 10 seconds.
A double-acting cylinder has a plunger of 10 cm in diameter. The diameter ratio between the plunger and the stem is 5. This cylinder is connected to a compressed air network at the pressure of 2 MPa and performs 15 cycles per minute. Assuming a friction force equal to 10% of the theoretical one, calculate: a) The force exerted by the stem in the advance race and the one exerted in the return race. b) The stroke length if the air flow, measured under normal conditions, is 583 l/min. c) What would be the section of a single-acting cylinder, working with traction, that would provide the same flow?
double sided centrifugal compressor has eye root and tip dia of 18 cm and 30 cm and is to deliver 16 kg/sec air at 16000 rpm. The designed ambient conditions are 15° C and 1 bar and compressor has to be a part of stationary power plant. Determine (1) Suitable value for impeller vane augles of root and tip of eye if the air is given 20° of pre whirl at all radii. Axial component of velocity is constant throughout the impeller and is 150 m/sec. (ii) Max. mach, no. at eye if C,= 1.005 kJ/kg, y=1.4.
p88#6. four pounds of air gain 0.491 Btu/degree Rankine of entropy during a nonflow isothermal process. if pa=120psia and V2=42.5ft^3, find (a)V1 and T1,(b)W,(c) Q and (d) internal energy.