A uniform beam of length L = 7.25 m and weight 4.65 x 102 N is carried by two workers, Sam and Joe, as shown in the figure below. Determine the force that each person exerts on the beam. Sam Joe 1.00 m +2.00 m→ L. FSam = N F1oe =

A uniform beam of length L = 7.25 m and weight 4.65 x 102 N is carried by two workers, Sam and Joe, as shown in the figure below. Determine the force that each person exerts on the beam. Sam Joe 1.00 m +2.00 m→ L. FSam = N F1oe =

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 85PQ

See similar textbooks

Related questions

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A: Calculate the position coordinates of points O, A, B, C, and D.

Q: 02 Pin

Q: A uniform 30 lb beam 10 ft long is carried by two men A and B, one at each end of the beam. a. If a…

A: The torque acting on an object is defined as the product of the perpendicular force acting on the…

Q: . A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam, a) IfA…

Q: In the figure shown, if the weight of the beam is 300 N. What is the force exerted ?by the beam on…

A: Given data: Weight of the beam = 300 N Need to determine the reaction force in the leg A.

Q: determines the consequence of the linear load acting on the beam

Q: What is the magnitude and direction of the single force applied to make the two concurrent forces…

A: A set of forces whose lines of action come through a common point iscalled concurrent forces.…

Q: The cantilevered beam is supported at the fixed support A as shown in Figure Q3.1. 6 kN 130 1 30°…

Q: A 2.0 m long uniform beam weighs 150.0N and supports a 550.0 N load at one end as shown in Figure 1.…

A: Given, A block hanged on a beam which is 2m long and weight 150.0 N

Q: A uniform pole 20 feet long and weighing 80 lbs is supported by a boy 2 feet from end A and a man 5…

Q: A uniform 33.5 kg beam of length e4.20 m is supported by a vertical rope located d 1.20 m from its…

Q: How to answer Fsam

A: the sum of the forces exerted on Sam and Joe is equal to the weight of the beam

Q: A bridge of length 50.0 m and mass 8.10 x 104 kg is supported on a smooth pier at each end as shown…

Q: You are asked to hang a uniform beam and sign using a cable that has a breaking strength of 415 N.…

Q: A gymnast with mass 46.0 kg stands on the end of a uniform balance beam as shown in the figure. The…

A: Concept Apply the torque concept Torque=Distace*Force

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500 N load.…

Q: 3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A…

A: Given: Length of beam, L=6 m Force due to beam, F=25 N Force by A, FA=20 N

Q: A uniform horizontal beam with a length of 9.1 m anda weight of 235.3 N is attached to a wall by a…

Q: The figure is attached A uniform beam of length L = 7.75 m and weight 4.00 ✕ 102 N is carried by…

Q: A traffic light hangs from a pole as shown in the figure below. The uniform aluminum pole AB is 6.50…

Q: What will happen when the supports are removed from this system? kg kg 1.75 1.5 1.25 1 0.75 0.5…

Q: A taho vendor carries a 1.5 m long light plank over his shoulder. At the ends of the plank are two…

A: Analyze the diagram of the given situation. Here, F and x represent the force exerted by his…

Q: A uniform plank of length 2.00 m and mass 29.0 kg is supported by three ropes, as indicated by the…

Q: A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A…

Q: 2 m 1 m F E 1.5 m 1.5 m MA H G mc = 30 Kg MB

Q: A uniform plank of length L=2.7m and weight W =735N is supported by three ropes as indicated in the…

A: Given information: The symbols have the same meaning as given in the question.

Q: A uniform pole 20 feet long and weighing 80 lbs is supported by a boy 2 feet from end A and a man 5…

A: (given) Uniform length of pole = 20 ft Weighing (W = 80 lbs) is supported by boy. A boy…

Q: A window washer is standing on a scaffold supported by a vertical rope at each end. The scaffold…

Q: A uniform rod weighing 15 kg is supported in a horizontal position by a pin and wire as shown in…

Q: In the figure shown, if the weight of the beam is 300 N. What is the force exerted by the beam on…

Q: A uniform 0.40 kN boom is supported as shown. Find the tension in the tie rope and the components of…

Q: A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and…

A: Given data: Mass of the plank m =20.0.kg Length of the plank l =4.00m The plank rest on two pivots,…

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

A: Free body diagram :

Q: A uniform beam of length L = 7.70 m and weight 4.95 x 10² N is carried by two workers, Sam and Joe,…

A: Given data: Length of the beam is, L= 7.70 m Weight of the beam is, W= 4.95×102 N Formula used: At…

Q: A uniform beam of length L = 7.70 m and weight 4.75 ✕ 102 N is carried by two workers, Sam and Joe,…

A: At equilibrium, the net force acting along the vertical direction is zero. So, the equation can be…

Q: 50 N 0.20 L 60 N 0.60 L 80 N 30 0 70

Q: The taho vendor carries a 1.5 m long light plank over his shoulder. At the ends of the plank are two…

A: Given data: Length of plank is, L=1.5 m. Weight of bucket at one end of plank is, W1=40 N. Weight of…

Q: What will be the total resultant force acting vertically in the figure given below consisting of a…

A: In this question we have to determine the total resultant force acting vertically on the figure…

Q: A taho vendor carries a 1.5 m long light plank over his shoulder. At the ends of the plank are two…

Q: The diagram shows a sign that wighs 50 N hanging from a uniform horizontal pole. The pole weighs 30…

A: The net torque about the axis is,

Q: Consider the 120-cm board supporting three loads as shown below. The beam weighs 45 grams. If the…

Q: A uniform horizontal beam with a length of 8 m and a weight of 200 N is attached to a wall by a pin…

A: Solution: given that L = 8 mF = 200 NW = 600 Nx = 2 mangle = 53 degree

Q: A uniform 34.0-kg beam of length { = 5.95 m is supported by a vertical rope located d = 1.20 m from…

A: A) Analyze the following figure. Since the beam is not rotating, the sum of the torque acting about…

Q: A uniform plank of length 2.00 m and mass 27.5 kg is supported by three ropes, as indicated by the…

Q: A uniform 120-lb beam is supported in a horizontal position by a pin and cable as shown in the…

A: Given, Weight of beam W = 120 lb Length of beam l = 12 ft Angle θ=37∘

Q: A carpenter carries a 6kg uniform board as shown below? (a) What downward force does he apply with…

A: Given Mass of board ,M = 6 kg Acceleration due to gravity ,g = 9.8 m/s2

Q: In a construction site, two vertical cables are supporting a 3.00m steel beam weighing 1500N.…

A: Given: Mg=1500 N T1 =2000N T2 = 3000 N We have to find m and x

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

A uniform beam of length L = 7.25 m and weight 4.65 x 102 N is carried by two workers, Sam and Joe, as shown in the figure below. Determine the force that each person
exerts on the beam.
Sam
Joe
1.00 m
+2.00 m→
L.
FSam =
N
F1oe =

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Express all answers in significant figures and scientific notation. 1. The second floor portion of a house is about to break down, so it was propped up by an iron column 4.0 meters long with cross sectional area of 30.0 cm^2. The iron column was compressed by 0.015 mm. How much load (N) the iron column is supporting? Y of Iron = 19 X 10^10 Pa
A man weighs 210 lbf at a location where g= 32.10 ft/s2. Determine his weight on the Mars, where g= 5.47 ft/s2.
A rod 120 cm long and of a diameter 3.0 cm is stretched by a force of 18 kN. What is its stress? a. 20. 70 N/mm^2 b. 25.47 N/mm^2 c. 245 N/mm^2 d. 2,470 N/mm^2
A copper wire of length 5.9 m , cross sectional area 2.6 x 10-6m2and Young’s modulus 11 x 1010 N/m2 has a 398 kg load hung on it. What is its increase in length? (g = 9.8 m/s2) ROUND TO 3 DECIMAL PLACES
The bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 3.91x107 N/m2? Assume that the force is applied uniformly over the surface. Round your answer to 3 decimal places.
An axial pull of 1.5 kN is acting on a bar of consisting two equal lengths as shown but of diameter 10cm and 20 cm respectively. What will be the stresses in the two sections respectively in N/mm2? A. 0.153 and 0.0036 B. 0.290 and 0.046 C. 0.190 and 0.0046 D. 0.124 and 0.124
A(b) = 1.28 m/s^2 ↓ (????????), Length of the rope L = 18 m
A cable supports a lift that moves up with an upward acceleration of 2 m/s2. Given that the Proportional limit stress =10.1x10^9 N/m2 and the cross-sectional area of the cable=6.5x10^-6 m2. Given that the gravitational acceleration is 9.8 m/s2. What is the maximum load that the lift can carry? (in Kg
A steel cable 3.00 cm2 in cross-sectional area has a mass of 2.40 kg per meter of length. If 500 m of the cable is hung over a vertical cliff, how much does the cable stretch under its own weight? Take Ysteel = 2.00 × 1011 N/m2.
The wooden sign is supported by three chains attached to the ceiling ( AC,AB,AD). If the tension in AB= 100 lbf and AC=65 Lbf, determine the tension in AD and the weight of the sign in equilibrium. 1 Determine the x component of the force AB: ABx= __lbf 2 Determine the Y component of force AB:ABy=__lbf 3 Determine the x component of force AC:ACx=__lbf 4 Determine the y component of the force AC:ACy =__lbf 5 Determine the magnitude of the force AD =__lbf 6 Determine the weight of the sign=__lbf
Assume the breaking stress of a bone is 1.30 x 107 N/m2, the magnitude of the maximum force a disease femur bone 3 cm in average diameter could withstand is
A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert?