You are asked to hang a uniform beam and sign using a cable that has a breaking strength of 415 N. The store owner desires that it hang out over the sidewalk as shown. The sign has a weight of 178.0N and the beam's weight is 37.0 N. The beam's length is 1.86 m and the sign's dimensions are 1.00 m horizontally x 0.80 m vertically. What is the minimum angle 0 that you can have between the beam and cable? Joe's 0.80 m AUTO SERVICE FESE EMATS- -1.00 m-

You are asked to hang a uniform beam and sign using a cable that has a breaking strength of 415 N. The store owner desires that it hang out over the sidewalk as shown. The sign has a weight of 178.0N and the beam's weight is 37.0 N. The beam's length is 1.86 m and the sign's dimensions are 1.00 m horizontally x 0.80 m vertically. What is the minimum angle 0 that you can have between the beam and cable? Joe's 0.80 m AUTO SERVICE FESE EMATS- -1.00 m-

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 90A

See similar textbooks

Similar questions

In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
Find the magnitude of the tension in each supporting cable shown below. In each case, the weight of the suspended body is 100.0 N and the masses of the cables are negligible.
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
a horizontal rod (m=5.2 kg) is hinged to a wall at the left end and three forces are acting on the rod as shown in the figure: the force of gravity (mg), a tension force (T), and the force exerted by the hinge (broken into components Fx and Fy) If theta = 35 degrees, what must T be equal to in order to keep the rod static?
You are asked to hang a uniform beam and sign using a cable that has a breaking strength of 417 N. The store owner desires that it hang out over the sidewalk as shown. The sign has a weight of 346 N and the beam’s weight is 78.0 N. The beam’s length is 1.50 m and the sign’s dimensions are 1.00 m horizontally × 0.800 m vertically. What is the minimum angle θ that you can have between the beam and cable? Answer in degrees
A museum of modern art is displaying an irregular 426-N sculpture by hanging it from two thin vertical wires, A and B, that are 1.25 m apart. The center of gravity of this piece of art is 48.0 cm from its extreme right tip. Find the tension in each wire.
A uniform steel bar of length 10 m is supported at point A and B using two cables as shown in the figure. The bar is hinged at point C and has a weight 500 N. What is the tension (T) force in the cable?
A diving board 3.00 m long is supported at a point 1.00 m fromthe end, and a diver weighing 500 N stands at the free end (Fig. ).The diving board is of uniform cross section and weighs 280 N. Find(a) the force at the support point and (b) the force at the left-hand end.
A 45 cm x 45 cm square plate ABCD of uniform thickness is supported by three vertical strings. The first string is located at B, the second is located 15 cm from A alongside AD and the third is at the point midway of side CD. What percent of the load is carried by the second support?
A uniform drawbridge must be held at a 36.5 angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 14.0 m long, and pivots about a hinge at its lower end. A cable is connected 4.00 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. A) What is the tension in the cable? Express your answer in newtons. B) Find the magnitude of the force the hinge exerts on the bridge. Express your answer in newtons. C) Find the direction of the force the hinge exerts on the bridge. Express your answer in degrees. D) If the cable suddenly breaks, what is the initial angular acceleration of the bridge? Express your answer in radians per second squared.
A uniform beam 4.2 m long and weighing 2200 N carries a 3700 N weight 1.50 m from the far end, as shown in the figure below. It is supported horizontally by a hinge at the wall and a metal wire at the far end. 1) How strong does the wire have to be? That is, what is the minimum tension it must be able to support without breaking? Express your answer in newtons. 2) What are the horizontal component of the force that the hinge exerts on the beam? Express your answer in newtons. 3) What are the vertical component of the force that the hinge exerts on the beam? Express your answer in newtons.
A painter stands on a uniform horizontal beam of length L = 6.0 m that is held in equilibrium by support cables attached to the roof as shown in Figure 3. The beam has a weight Wb = 250.0 N and the tensions on the left and the right ends are measured to be Tl = 360.0 N and Tl = 200.0 N respectively. A. Calculate the weight of the painter Wp , and Wb. the distance x where the painter is standing.