a uniform beam of weight 500 N and length 3.0 m is suspended horizontally. On the left it is hinged to a wall; on the right it is supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. (a) What value of D corresponds to that tension? (b) To prevent the cable from snapping, should D be increased or decreased from that value?

a uniform beam of weight 500 N and length 3.0 m is suspended horizontally. On the left it is hinged to a wall; on the right it is supported by a cable bolted to the wall at distance D above the beam. The least tension that will snap the cable is 1200 N. (a) What value of D corresponds to that tension? (b) To prevent the cable from snapping, should D be increased or decreased from that value?

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
a uniform beam with a weight of 60 N and a length of 3.2 m is hinged at its lower end, and a horizontal force of magnitude 50 N acts at its upper end.The beam is held vertical by a cable that makes angle u = 25° with the ground and is attached to the beam at height h = 2.0 m. What are (a) the tension in the cable and (b) the force on the beam from the hinge in unit-vector notation?
A sign is supported by a uniform horizontal boom of length 3.10 m and weight 72.0 N. A cable, inclined at an angle of 16 °with the boom, is attached at a distance of 2.71 m from the hinge at the wall. The weight of the sign is 108.0 N. What is the tension in the cable and what are the horizontal and vertical forces Fx and Fy exerted on the boom by the hinge? Comment on the magnitude of Fy. T= In N Fx= in N Fy= in N The magnitude of Fy is select (small or large) compared to that of Fx and T.
a uniform rod of mass m is hinged to a building at its lower end, while its upper end is held in place by a rope attached to the wall. If angle u1 = 60°, what value must angle u2 have so that the tension in the rope is equal to mg/2?
One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.
A uniform horizontal beam 5.00 m long and weighting 3.03 102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05 102 N stands 1.60 m from the wall, find the magnitude of the tension in the cable and the force exerted by the wall on the beam. T = N Rx = N Ry = N Even if we selected some other axis for the torque equation, the solution would be the same. For example, if the axis were to pass through the center of gravity of the beam, the torque equation would involve both T and Ry. Together with Equations (1) and (2), however, the unknowns could still be found—a good exercise. In this example, notice the steps of the Problem-Solving Strategy could be carried out in the explicit recommended order.QUESTION What happens to the tension in the cable if the man in Figure (a) moves farther away from the wall? The tension would…
A uniform plank of length 2.00 m and mass 30.0 kg is supported by three ropes, as indicated by the blue vectors. Find the tension in each rope when a 700 N person is d = 0.500 m from the left end
The system is in equilibrium. A concrete block of mass 225 kg hangs from the end of the uniform strut of mass 45.0 kg. A cable runs from the ground, over the top of the strut, and down to the block, holding the block in place. For angles f = 30.0° and u = 45.0°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge.
suppose the length L of the uniform bar is 3.4 m and its weight is 180 N. Also, let the block's weight W = 310 N and the angle 0 = 41°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?