A uniform concrete slab of mass M is to be attached to two rods whose lower ends arw initially at the same level. find: The area of aluminium bar so that slab will remain level after it is attached to the rods. The stress in the steel rod if M=18000kg The stress in aluminum rod if M=18000kg The elongation of the streel rod The elongation of the aluminum rod.

A uniform concrete slab of mass M is to be attached to two rods whose lower ends arw initially at the same level. find: The area of aluminium bar so that slab will remain level after it is attached to the rods. The stress in the steel rod if M=18000kg The stress in aluminum rod if M=18000kg The elongation of the streel rod The elongation of the aluminum rod.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.5.7P: Solve the preceding problem for a column with e = 0.20 in,, L = 12 ft, I = 2L7in4, and E = 30 ×...

See similar textbooks

Similar questions

Dinding ruang penyimpanan berpendingin adalah panjang 10 m dan tinggi 3 m dan dibangun dengan blok beton 100 mm (k = 0.935 W / [m °C]) dan 12 cm papan isolasi serat (k = 0,048 W). / [m °C]). Suhu ruang pendingin -10 °C dan koefisien perpindahan panas konvektif adalah 40 W / (m² K); suhu udara luar adalah 30 °C dengan koefisien pindahan panas konveksi permukaan dinding luar 10 W / (m² K). Hitung koefisien perpindahan panas keseluruhan. Koefisien pindah panas keseluruhan =AnswerW / (m² K).
ε0= 0.005B (hr-1Pa-1)=4.20E-34n=3.15 σ0 (Pa)= 550000000
Take Young's Modulus = 12.5kN/mm2
With pressure steel tank axis α = 750manufactured as degree angle helical weldedreferences Tank radius r = 0.80 m. wall thickness is 15 mm The internal pressure of the Tank is p = 2.8 kPa. Elasticity modulus of steel used in manufacturing e = 200 GPa and position repair ν = 0.3 stop For the cylindrical part of the tank; a-) Find circular and longitudinal stresses. b-) Find the largest in-plane and out-plane shear stresses. c-)Find a circular and longitudinal shape change. d-)Find normal and shear stresses formed in the welding seam. These stressesshow on the properly rotated element.
L=9m W=5kN/m 360 UB 50.7
A link of a valve gear has to be curved in one plane, for the sake of clearance. Estimate the maximum tensile and compressive stress in the link if the thrust is 2500 N. (Cam bridge) ANSWER: maximum tensile 38.0 MN/m2; maximum compressive 46.0 MNIm2. Please show the solution to get the answer.
find the longitudinal strtain experienced by the strut it width is 8mm and height is 20mm
STRENGTH OF MATERIALS W/SOLUTION 1.) A penstock pipe 10m diameter carries water under a pressure head of 100m. If the wall thickness is 9mm, the tensile stress in the pipe wall is nearest to? A. 2725 B. 1090 C. 545 D. 110 E. NOTA
Property ASTM A710 Steel AA 7075 Density 7.8 2.81 Yield Strength 585 503 Ultimate Tensile Strength 620 572 Poisson Ratio 0.29 0.33 Shear Modulus 80 26.9 Young’s Modulus 205 71.7 Dimensions Side bar (C-Channel) = 210 x 76 x 6 mm Front Overhang = 935 mm Rear Overhang = 1620 mm Wheel Base = 3800 mm Width = 2250 mm Capacity = 8000 x 9.81 = 78480N Capacity with 1.25% = 98100N Weight of body and engine = 19620N Total load = 117720N Load acting on a single bar of chassis = 58860N Using the information above for two materials Iron (ASTM A710 Steel ) and Aluminum (AA 7075) Calculate for each Material Reaction Force Shear Forces Bending Moment Bending Stress Shear Stress Von Misses Stress Principle Stress Max Shear Stress Total Deflection Draw the Shear Force and bending moment Diagram for each Material. Draw the Equivalent Mohr Circle for each material Conclude with a Comparison of the Deformation of the two Materials.
Find the amount of depression in mm at the midpoint of the bar AB. Mo= 1kNm, L = 1m, E = 200 GPa, I=1x106mm4
A steel pipe of length L= 3 ft, outside diameter d₂- 10 in., and inside diameter dy = 5.1 in. is compressed by an axial force P= 107 kips. The material has = Poisson's ratio v=0.30. Determine the increase in thickness.
Find the amount of depression in mm at the midpoint of the bar AB.Mo = 1kNm, L = 1m, E = 200 GPa, I=1x106 mm4