A uniform, solid, 100-kg cylinder with a diameter of 1.0 m is mounted so it is free to rotate about fixed, horizontal, frictionless axis that passes through the centers of its circular ends. A 10-kg block is hung from a very light thin cord wrapped around the cylinder's circumference. When the block is released, the cord unwinds and the block accelerates downward, as shown in the figure. What is the acceleration of the block in mls2? Answer:

A uniform, solid, 100-kg cylinder with a diameter of 1.0 m is mounted so it is free to rotate about fixed, horizontal, frictionless axis that passes through the centers of its circular ends. A 10-kg block is hung from a very light thin cord wrapped around the cylinder's circumference. When the block is released, the cord unwinds and the block accelerates downward, as shown in the figure. What is the acceleration of the block in mls2? Answer:

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 75P: A wad of sticky clay with mass m and velocity vi is fired at a solid cylinder of mass M and radius R...

See similar textbooks

Similar questions

The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4 kg and its radius is 30 cm, as well as the distance from the center of mass to the pivot, what is the rotation rate in rev/s of the disk?
A uniform rod of length L and mass M is held vertically with one end resting on the floor as shown below. When the rod is released, it rotates around its lower end until it hits the floor. Assuming the lower end of the rod does not slip, what is the linear velocity of the upper end when is hits the floor?
Check Your Understanding What is the moment of inertia of a cylinder of radius R and mass m about an axis through a point on the surface, as shown below? A uniform thin disk about an axis through the center Integrating to find the moment of inertia of a two-dimensional object is a little bit trickier, but one shape is commonly done at this level of study—a uniform thin disk about an axis through its center (Figure 10.27). Figure 10.27 Calculating the moment of inertia for a thin disk about an axis through its center.
A hollow cylinder that is rolling without slipping is given a velocity of 5.0 m/s and rolls up an incline to a vertical height of 1.0 m. If a hollow sphere of the same mass and radius is given the same initial velocity how high vertically does it roll up the incline?
A 40.0-kg solid cylinder is rolling across a horizontal surface at a speed of 6.0 m/s. How much work is required to stop it?
A top has moment of inertia 3.2104kgm2 and radius 4.0 cm from the center of mass to the pivot point. If it spins at 20.0 rev/s and is precessing, how many revolutions does it precess in 10.0 s?
The moment of inertia of a long rod spun around an axis through one end perpendicular to its length is mL2/3 . Why is this moment of inertia greater than it would be if you spun a point mass m at the location of the center of mass of the rod (at L/2 ) (that would be mL2/4 )?
A baseball catcher extends his arm straight up to catch a fast ball with a speed of 40 m/s. The baseball is 0.145 kg and the catcher’s arm length is 0.5 m and mass 4.0 kg. (a) What is the angular velocity of the arm immediately after catching the ball as measured from the arm socket? (b) What is the torque applied if the catcher stops the rotation of his arm 0.3 s after catching the ball?
While punting a football, a kicker rotates his leg about the hip joint. The moment of inertia of the leg is 3.75kgm2 and its rotational kinetic energy is 175 J. (a) What is the angular velocity of the leg? (b) What is the velocity of tip of the punter’s shoe if it is 1.05 m from the hip joint?
Big Ben (Fig. P10.17), the Parliament tower clock in London, has hour and minute hands with lengths of 2.70 m and 4.50 m and masses of 60.0 kg and 100 kg, respectively. Calculate the total angular momentum of these hands about the center point. (You may model the hands as long, thin rods rotating about one end. Assume the hour and minute hands are rotating at a constant rate of one revolution per 12 hours and 60 minutes, respectively.)
Suppose a child walks from the outer edge of a rotating merry-go-round to the inside. Does the angular velocity of the merry-go-round increase, decrease, or remain the same? Explain your answer. Assume the merry-go-round is spinning without friction.
A playground merry-go-round of radius R = 2.00 m has a moment of inertia I = 250 kg m2 and is rotating at 10.0 rev/min about a frictionless, vertical axle. Facing the axle, a 25.0-kg child hops onto the merry-go-round and manages to sit down on the edge. What is the new angular speed of the merry-go-round?