a) Using a NTC thermistor with "B=4000K, resistance: 5kN at 25°C" we want to measure the temperature of an environment in the range 50°C - 100°C. Design a suitable circuit for this purpose with "zero" output signal (v) value at 25ºC. Express the output and its temperature-sensitivity in terms of temperature (y=f(T°C) and dy/dT= f(T°C)). Roughly draw y and dy/dT for the given temperature range. (Note: For NTC: RATC=Roexp(B(1/T-1/T)

a) Using a NTC thermistor with "B=4000K, resistance: 5kN at 25°C" we want to measure the temperature of an environment in the range 50°C - 100°C. Design a suitable circuit for this purpose with "zero" output signal (v) value at 25ºC. Express the output and its temperature-sensitivity in terms of temperature (y=f(T°C) and dy/dT= f(T°C)). Roughly draw y and dy/dT for the given temperature range. (Note: For NTC: RATC=Roexp(B(1/T-1/T)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Considering the amplifier gain 13 and the number 2 as N, design a Wien Bridge oscillator circuit with an oscillating frequency ((1 + N) × 1000) Hz. Draw the circuit. Show the process steps. Show the values of the circuit elements in your drawing. I would be very happy if you could be quick :)
7. When the automatic gain control voltage of a radio receiver is measured with a vacuum tube voltmeter whose input resistance is 10 M-ohm, it reads 4.5 V. When an ordinary voltmeter whose input resistance is 10 k-ohm is also connected across the AGC voltage source, both meters read 0.40. What is the internal resistance of the AGC voltage source? 8. A phonograph pick up develops an open-circuit emf of 50 mV and has an internal resistance of 1200 ohm. A. What voltage will it develop across a 4 ohms load resistance? B. What value of load resistance must be used to obtain a 75% eff? C. What is the maximum power output of the pickup? 9. What bleeder resistor is required to complete a voltage divider to give 300 v at 40 mA from a 500 V source of emf if the series dropping resistor is 4 k-ohm.
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100 kiliohm. R1 = R3 = 10 kiliohm, R5 = 10 kiliohm, R6 = 90 kiliohm. and R5 = 10 kiliohm. The load resistor R7 = 10 kiliohm. The current source; I1 = 100μA and V2 = 1V.
1. Find the Thévenin equivalent circuit with respect to the output terminals a, b for the inverting amplifier shown. The dc signal source has a value of 880 mV. The op amp has an input resistance of 500 kΩ, an output resistance of 2 kΩ, and an openloop gain of 100,000. 2. What is the output resistance of the inverting amplifier? 3. What is the resistance (in ohms) seen by the signal source vs when the load at the terminals a, b is 330 Ω?
Consider ab N-bit DAC whose output varies from 0 to VFS (where the subscript FS denotes "full scale"). (a) Show that a change in the least significant bit (LSB) induces a change of VFS/(2N-1) in the output.This is the resolution of the converter. (b) Convince yourself that the DAC can produce any desired output voltage between 0 and VFS with at most VFS/2(2N-1) error (i.e., one-half the resolution). This is called quantization error of the converter. (c) For VFS = 5 V, how many bits are required tp obtain a resolution of 2 mV or better? What is the actual resolution obtained? What is the resulting quantization error?
For the circuit in the figure below, design the value of R_2 to obtain an output voltage of 2 V when the input differential voltages (V1–V2) is equal to 20 mV.
Question 7 For an op-amp amplifier circuit has a closed-loop voltagegain of 5. If the op-amp used has a gain-bandwidth productof 1.5 MHz, and we can only tolerate 10% drop in gain, whatwill be the maximum usable frequency? (help me do this question with explanation)
For an op-amp having a slew rate SR = 8 V/ms, what is the maximum closed-loop voltage gain that can be used when the input signal varies by 0.5 V in 10 ms? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.
An op-amp with an open-loop gain of 6x105 and Vcc = 15 V has an output voltage of 3 Volts. If the inverting-input voltage is -1.8 microVolts then determine the non-inverting input voltage in microVolts to the single digit decimal place. Do not enter units. For example, if you calculate 3.1x10-6 Volts as your answer then enter 3.1. Similarly, if you calculate 1.872 x10-5 Volts as your answer then enter 18.7 (since this is 18.7 microvolts).
An op amp has Rid = 500 kΩ, Ro = 35 Ω, and A =5×104. You must decide if a single-stage ampliﬁer can be built that meets all of the speciﬁcations below. (a) Which conﬁguration (inverting or noninverting) must be used and why? (b) Assume that the gain speciﬁcation must be met and show which of the other speciﬁcations can or cannot be met. |Av| = 200 Rin ≥ 2×108 Ω Rout ≤ 0.2 Ω
The circuit shown in Figure1, given that R C = 3 KΩ, R L=1KΩ, V CC = 15 V, voltage gain Av=10v and IB = 10mA. The circuit has an input signal vin of =2v. Determine the value of IC.
What are the output current and output resistance of the current source as shown if VDD = 10 V, R4 = 2 MΩ, R3 = 1 MΩ, RS = 120 kΩ, Kp = 750 μA/V2, VT P = −0.75 V, and λ = 0.01 V−1?