A wastewater sample has 7.5 x 105 CFU per liter. The allowable fecal coli form concentration is 3500 CFU/L. What should be the length of carrying this wastewater if the flow velocity of the wastewater is 0.75 m/s and the reaction rate constant of decomposition of fecal coliform is 0.24 min-1.
Q: Q1: Design an activated sludge process to treat a wastewater of 15000 m³/day with a BODs of 180 mg/l…
A:
Q: Assume that a large stream has a reoxygenation constant k1' of 0.4/day, a flow velocity of 5…
A: Given Data:k1= 0.4/dayFlow velocity= 5miles/hour=2.24m/sOxygen= 10mg/Loxygen demand=…
Q: Question 2 ) A primary wastewater treatment uses centrifugation for dewatering of primary…
A: Given :- Average daily flow of sewage to the treatment plant = 5000 m3/day Total suspended solids in…
Q: The 5-day BOD of a wastewater sample is obtained as 190 mg/L (with k = 0.01 h-¹). The ultimate…
A: Given data- 5 Day BOD- Lt=190 mg/L,decay constant-k=0.01 h-1=0.01×24 day-1.⇒kD=0.434k.time t= 5…
Q: Waste, measured as BOD, is removed according to first order kinetics at a rate constant of 0.4…
A: We knowBODt=BODY1-e-ktso for ·%BODtBODy=100-80=20%so,0.2=1-e-0.4tt=1.9348min
Q: A sewage treatment plant discharges 4 ML/d of effluent with 20.17 mg/L BOD5 into a stream. The…
A:
Q: The aeration tank for a completely mixed aeration process is being sized for a design wastewater…
A:
Q: A schematic flow diagram of a completely mixed biological reactor with provision for recycling of…
A: given- discharge Q=15000 m3/ddetention time HRT=2 hrs=224daysX=3000 mg/Lwasted sludge Qw=50…
Q: b) Determine the concentration of the effiuent BOD, for the two-stage trickling filter described…
A: DESIGN FLOW = 0.0509m3/s influent BOD5=260 mg/l diameter of each filter = 24 m depth of each filter=…
Q: Wastewater of 30ft3/s with a biochemical oxygen demand (BOD) of 55mg/l, and dissolved oxygen (DO) of…
A:
Q: Design a facultative pond to treat 12900gpm of sewage having 645mg/L of BOD. The average summer and…
A:
Q: Wastewater of 30ft°/s with a biochemical oxygen demand (BOD) of 55mg/I, and dissolved oxygen (DO) of…
A:
Q: (a) Design an oxidation pond for treating sewage from a hot climatic residential colony with 4000…
A: The quantity of sewage to be treated per day. = 4000 X 180 = 720,000 litres = 720 cu.m The BOD…
Q: The wastewater contains 7.5 x 105 fecal CFU per liter. The maximum permissible fecal coliform…
A: Given: Initial coliform concentration, Co = 7.5 x 105 CFU/L Maximum permissible coliform…
Q: Wastewater from a primary treatment tank is to undergo secondary treatment in an activated sludge…
A: Given data-Hydraulic retention time (t) is 6hMean cell residence time is 7 daysBOD content at inlet…
Q: An aeration tank receives 10,000 m3/d of wastewater with a BOD loading of 2100 kg/d. The aeration…
A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…
Q: A factory is discharging its wastewater into a slowly moving stream that has a mean velocity of 3…
A: Dissolved oxygen sag curve
Q: na wastewater treatment plant, 35 mg/L of ammonia was nitrified to oxidized nitrogen in the…
A: Wastewater Treatment Plant : In wastewater treatment plant combination of various process such as…
Q: A wastewater is to be disinfected with 35 mg/L of chlorine to obtain 99% kill of micro-organisms.…
A: Given- 35 mg/L chlorine99% micro-organisms to be killedNt=Noe-ktk=0.23 min-1It is needed to find out…
Q: Wastewater is treated with a certain amount of chlorine to remove 97% of micro-organisms present in…
A: Given data : Flow rate,Q = 35m3/h = 0.583 m3/min depth, D= 1.4 m width, W= 1.1 m rate of kill, k =…
Q: The wastewater contains 7.5 x 105 fecal CFU per liter. The permissible fecal coliform concentration…
A: Given: Initial coliform concentration, Co = 7.5 x 105 CFU/L Maximum permissible coliform…
Q: A wastewater sample contains two nitrogen species, namely ammonia and nitrate. Consider the atomic…
A: Given data:- A wastewater sample contains two nitrogen species, namely ammonia and nitrate. To…
Q: Wastewater with DO concentration of 2 mg/L is discharged to a river. The temperature of the river is…
A:
Q: A wastewater is to be disinfected with 35 mg/Lof chlorine to obtain 99% kill of micro-organisms. The…
A:
Q: Design an activated sludge system for the wastewater flowing at the average rate of (10650)GPM…
A: Introduction : Microorganisms are combined with wastewater in the activated sludge process.…
Q: () A wastewater sample is being analyzed to determine its BOD content. The sample is diluted in…
A: Volume of wastewater sample=5 mL Volume of distilled water added to sample for dilution=295 mL Total…
Q: Wastewater is treated with a certain amount of chlorine to remove 97% of micro-organisms present in…
A: Given: Removal percentage = 97% Rate of kill for treatment, k = 0.21 min-1 Flow rate of wastewater,…
Q: The wastewater from a synthetic textile manufacturing plant is discharged to a municipal treatment…
A: Given: Textile plant: BOD = 1500 mg/l SS = 2000 mg/l Nitrogen = 30 mg/l Phosphorous = 0 Domestic:…
Q: A wastewater sample contains two nitrogen species, namely ammonia and nitrate. Consider the atomic…
A: Given, The atonic weight of N, H, and O as 14 g/mol, 1 g/mol and 16 g/mol respectively Concentration…
Q: A primary wastewater treatment uses centrifugation for dewatering of primary sedimentation sludge.…
A: Given :- Average daily flow to the treatment plant = 5000 m3/d Total suspended solids in raw waste…
Q: A wastewater with a BOD of 25mg/L is discharged through an outfall to a freshwater stream of mean…
A: BOD = 25 mg/LMean velocity of freshwater stream = Vmean-fresh = .1m/sDOdownstream =…
Q: An activated sludge treatment plant treats a sewage at a flow of 3*10^6 I/day with a BOD of 350…
A: FM is food by microorganisms…
Q: Design an oxidation pond to treat waste water from a community of 10,000 people with a per capita…
A:
Q: The wastewater contains 7.5 x 105 fecal CFU per liter. The permissible fecal coliform concentration…
A: Given: Initial coliform concentration, Co = 7.5 x 105 CFU/L Maximum permissible coliform…
Q: Wastewater of 30ft3/s with a biochemical oxygen demand (BOD) of 55mg/l, and dissolved oxygen (DO) of…
A: Given: The wastewater flow is 30 ft3/s. The characteristic of wastewater is, The river flow is 125…
Q: An existing single-stage rock trickling filter treats a wastewater flow of 3785 m/d ("raw" influent…
A:
Q: A CMAS treatment system must be designed for a municipal wastewater and the following operating…
A: The given data is: BOD5=0.39m3/s VSS in the aeration tank=4300 mg/L 55 g VSS=100 gm soluble BODs…
Q: A rural village with 70 people equivalent(p.e.) is nearby a 30 cm deep, 1 m wide pristine river…
A:
Q: The wastewater contains 7.5 x 105 fecal CFU per liter. The permissible fecal coliform concentration…
A: Given: Initial coliform concentration, Co = 7.5 x 105 CFU/L Maximum permissible coliform…
Q: An activated sludge wastewater treatment system was designed and operated in a steady state under…
A: Given, Reactor volumeV=10000 m3Sludge concentration MLSSX=3200 mg/lreturn sludge…
Q: A lagoon with a volume of 1200 m3 has been receiving a steady flow Q = 100 m3/day of a…
A: The given data is shown below:
Q: An activated sludge treatment plant treats a sewage at a flow of 3*10^6 I/day with a BOD of 350…
A:
Q: Dechlorination contact tank (Wastewater Treatment) An activated sludge plant has a design flow…
A: Given data: Number of tank =1 Detention time = 30 sec Depth = 10 ft For rectangular tank: L = 4 W…
Q: The pipe carrying wastewater contains 5.5 x 105 fecal CFU/liter. Determine the length of pipe…
A: Given: Coliform concentration, Co = 5.5 x 105 CFU/Liter Maximum permissible concentration, C = 3000…
Q: The 5-day BOD of a wastewater sample is obtained as 190 mg/l (with k = 0.01 h1). The ultimate oxygen…
A:
Q: An industry has decided to treat its process wastewater in a biotower with a plastic modular medium…
A: Given: The flow rate of the waste water is 1400 m3/day. The BOD5 is 630 mg/l. The depth of the…
Q: A wastewater sample has 7.5 x 105 CFU per liter. The allowable fecal coli form concentration is 3500…
A: Given: Initial coliform concentration, Co = 7.5 x 105 CFU/L Allowable coliform concentration, C =…
WASTEWATER ENGINEERING:
A wastewater sample has 7.5 x 105 CFU per liter. The allowable fecal coli form concentration is 3500 CFU/L. What should be the length of carrying this wastewater if the flow velocity of the wastewater is 0.75 m/s and the reaction rate constant of decomposition of fecal coliform is 0.24 min-1.
Step by step
Solved in 4 steps with 4 images
- The rate of eradicating microbes through chlorination process is 0.22/min when the wastewater is flowing at a rate of 36 m3/h. If the depth of chlorination tank is 1.6 m and the width is 1.2 m, determine the required length of the tank to achieve 98% removal.A wastewater treatment plant discharges 2.16x107 L/hr of treated effluent with an ultimate BOD of 22.0 mg/L and dissolved oxygen concentration of 5.0 mg/L to a river. Upstream of the waste discharge, the river has a flow of 9.0 m3/s, an ultimate BOD of 10.0 mg/L, and dissolved oxygen concentration of 7.0 mg/L. Both the river and effluent are at 20°C. After the river and effluent mix, the river flows at a velocity of 0.13 m/s and has a depth of 1.8 m. The deoxygenation rate constant for the waste is 0.45 day-1. A fish hatchery is located 9.6 km downstream of the waste discharge. The hatchery requires 5.0 mg/L DO for healthy fish growth and reproduction. Is the hatchery requirement being met? show all workThe wastewater contains 7.5 x 105 fecal CFU per liter. The permissible fecal coliform concentration is 3500 fecal coliform CFU/L. Calculate the length of pipe required if the linear velocity of the wastewater pipe is 0.73 m/s. Take the reaction rate constant for the destruction of the fecal coliform is 0.21 per min.
- The wastewater from a synthetic textile manufacturing plant is discharged to a municipal treatment plant for processing with domestic wastewater. The characteristics of the synthetic textile wastewater are 1500 mg/L BOD, 2000 mg/L SS, 30 mg/L nitrogen, and no phosphorus. The characteristics of the domestic wastewater are 200 mg/L BOD, 240 mg/L SS, 35 mg/L nitrogen, and 7 mg/L phosphorus. Find the BOD, SS of the mixture. The ratio of flow rate is domestic/textile = 4/1The density of water at 4°C is 1000 kg/m3 at atmosphericpressure. The gravity acceleration constant (g) is 9.81 m/s2. Thespecific gravity of an industrial wastewater (SGww) is 1.32. Whatis the specific weight of this wastewater?Estimate the membrane area required as a part of membrane bioreactor (MBR) process design for the treatment of wastewater with a flow rate of 5000 m3/d. Design flux, J= 20 LMH (L/m2.h)
- Assume that DLSUD lake is 100m2 and its average height is 5ft. Wastewater that flows into the lake are the following: Food square kitchen waste 7 m3/sec; Total Dissolved Solids (TDS) is 25,000 mg/L which operates 8hrs per day CIH 5m3 /hr kitchen waste; TDS is 20mg/L which operates 4hrs per day PCH 20m3 /day diluted laboratory waste ; TDS = 40mg/L (1)Determine the volumetric flow rate of the lake water can still accommodate prior to rainfall.The wastewater contains 7.5 x 105 fecal CFU per liter. The maximum permissible fecal coliform concentration is 3500 fecal coliform CFU/L. Determine the length of pipe required if the linear velocity of the wastewater pipe is 0.75 m/s. Assume the reaction rate constant for the destruction of the fecal coliform is 0.24 per min.You have a DAF with wastewater flow of 650 L/min, with a solids concentration of 15 g/L. Density of the wastewater is 1100 kg/m3. What air flow is required for an air to solids ratio of 0.3. Assume density of air is 1.2 kg/m3.
- A primary clarifer removes 35% of BOD5 and 55% of suspendedsolids from the incoming wastewater. Calculate the mass of solidsand mass of BOD5 removed in kg/d for a plant processing 4500 m3/dof wastewater with 275 mg/L BOD5 and 400 mg/L SS.An industry generates 4 million gallons per day (MGD) (that is 15,000 m^3/ day) of liquid industrial wastewater having BOD5 of 1000 mg/L and first order reaction rate constant of 2.0/day. Because of the high BOD, there is a plan to build an industrial pre-treatment system at an industrial park. Effluent from the pre-treatment will be discharged into the city sewer for final polishing at the city wastewater treatment plant. Determine: a. Percent BOD removal if the wastewater is treated in one 5000 m^3 continous flow stirred tank reactor. b. Percent BOD removal if the wastewater is treated in one 5000 m^3 plug flow reactor. c. Percent BOD removal if the wastewater is treated in one 2500 m^3 continous flow stirred tank reactor followed by one 2500 m^3 plug flow reactor. d. Percent BOD removal if the wastewater is treated in one 2500 m^3 plug flow reactor followed by one 2500 m^3 continous flow stirred tank reactor. e. Percent BOD removal if the wastewater is treated in one 2500 m^3…a. The wastewater from a manufacturing treatment plant is discharged to a municipal `treatment plant for processing with domestic wastewater. The characteristics of the wastewater from the manufacturing treatment plant are 3500 mg/l BOD, 4500 mg/l SS, 70 mg/l nitrogen and 2 mg/l phosphorous. The characteristics of the domestic wastewater are 350 mg/l BOD, 285 mg/l SS, 50 mg/l N and 11 mg/l P. If the required BOD/N/P weight ratio is 100/5/1, what is the minimum quantity of domestic wastewater required per 1000 gallons of manufacturing wastewater to provide adequate nutrients for biological treatment and the concentration of SS in the combined wastewater? b. What additional of NH4OH and H3PO4 would be required in pounds per million gallons of wastewater to provide the necessary nutrient levels for the treatment of the manufacturing wastewater described above (a) if the domestic wastewater had not been combined with it.