A water tank weighing 68000kg is supported by four vertical pipe columns with fixed ends, as shown in the figure below. The bending stiffness El of each column is 5.85x10° kg.cm?, and the column height is 7.30 m. Omit the distributed mass of the column, try to calculate the period of free vibration of the water tank in the horizontal direction.

A water tank weighing 68000kg is supported by four vertical pipe columns with fixed ends, as shown in the figure below. The bending stiffness El of each column is 5.85x10° kg.cm?, and the column height is 7.30 m. Omit the distributed mass of the column, try to calculate the period of free vibration of the water tank in the horizontal direction.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reciprocating pump, of mass 68.6 kg, is mounted at the middle of a steel plate of thickness 0.8 cm, width 50.4 cm, and length 279 cm, clamped along two edges as shown in the accompanying figure. During operation of the pump, the plate is subjected to a harmonic force F(t)=301 cos(84.60t) N. Find the amplitude of vibration of the plate. Given that the equivalent stiffness of the plate can be calculated as k=192EI / l^3and the young modulus is E=200 GPa.
An electrical switch gear is supported by a crane through a steel cable of length 4 m and diameter 0.01 m. If the natural time period of the axial vibration of the switch gear is found to be 0.01 s, find the mass of the switch gear. * 871 kg 1030 kg 1110 kg 955 kg
A shaft 60 mm diameter and 4 m long is simply supported at both ends and carries three vertically downwards point-loads of magnitudes 900 N, 1000 N, and 850 N located at 1 m, 2 m, and 3 m from the left support, respectively. The Young's modulus for shaft material is 110 GN/m2. 3.1. Provide the diagram of the position of supports and loads on the shaft3.2. Calculate the natural frequency of transverse vibration of the shaft.
For a Tall Tower under internal pressure and wind load as shown in the figure below, a) Calculate the minimum required thickness for shell. b) Determine the maximum allowable period of vibration for the Tall Tower with thickness of skirt at the base 1 [in], and weight of tower 150000 [lb].
The damped frame was subjected to free vibration at W=1000 kN, u0=L+10cm. If the amplitude measured in the first period is 9 cm and t= L+1s at this time, what is the damping ratio (h), critical damping ratio, damping coefficient (c). L=2
A box that contains of a 250 kg fragile instrument is transported by a truck that is subjected to a vertical harmonic motion given by ?(?) = 0.02 sin 3?. Assume that the instrument only moves in vertical translation and is supported by four springs with stiffness, k = 500N/m as simplified in Figure Determine the maximum displacement, velocity and acceleration experienced by the instrument
Determine the steady-state amplitude of the mass center of the bar of Fig P6.3 when its right end is subject to a moment M=4000sin105t N.m. Expected answer X=0.988mm
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
A four-cylinder automobile engine must be supported on three shock mounts,as shown in the picture. The engine block assembly weighs500 lbs. If the unbalanced force produced by the engine is given by200 sin 100 t lb, design three shock mounts (each stiffness k andviscous damping constant c) such that the vibration amplitudemaximum 0.1 in
A 3.00m long steel wire is fixed in a ceiling and a mass of 12.3kg is hanging from the wire. The wire has a diameter d=0.80mm, a Young’s modulus 2.00GPa and mass density 7860kg/m^3 d) Calculate the transverse speed of pulse e) calculate the longitudinal sound speed
A machine tool with mass m = 1000 kg and mass moment of inertia J0 = 300 kg/m² rests on elastic supports, as shown in the figure. If the stiffnesses of the supports are given by k1 = 4000 N/mm and k2 = 3000 N/mm, and the supports are located at l1 = 0.4 m and l2 = 0.7 m, determine the natural frequencies and modal forms of the machine -tool.
A rigid block of mass ? is mounted on four elastic supports, as shown in the figure. A mass ? drops from a height ? and adheres to the rigid block without rebounding. If the spring constant of each elastic support is ?, derive the equation of motion and find the natural frequency of vibration of the system (a) without the mass ?, and (b) with the mass ?. Also, find the resulting motion of the system in case (b). By using lagrange energy method