(a) What is the function of Digital to Analog Converter (DAC)? Mention its types. Write the truth table of 3 bit DAC. (b) Identify the following elements of the given closed loop control system. , (1) Process Element (ii) Feedback Element (ii) Control Element (iv) Correction Element Battery Speed Turntable Speed setting DC DC motor amplifier Tachometer

(a) What is the function of Digital to Analog Converter (DAC)? Mention its types. Write the truth table of 3 bit DAC. (b) Identify the following elements of the given closed loop control system. , (1) Process Element (ii) Feedback Element (ii) Control Element (iv) Correction Element Battery Speed Turntable Speed setting DC DC motor amplifier Tachometer

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

2a.Name three drawbacks of a digital system over an analog systems 2b. If a computer runs at 12.8 GHz, what is the period of its clock signal?
- Draw the control word format for 8253 timer with proper description of each field - Design a system to explain the digital data transmission using modem - Write the mode instruction format required to program the 8251A USART for asynchronous transmission with 8 data bits, 1 1/2 stop bits, odd parity. and transmitter clock frequency is 19200 Hz and transmit data at 1200Bd.
Computer Science Lab 8 PWM in C Generate PWM codes in C using the ACLK to create a wave form of 150Hz with duty cycle of 20% and 75%. Run in low power mode 3. Connect each wave to the red LED and observe the brightness difference. Display each wave with an oscilloscope and include the display in the report.
An absolute optical encoder has10 rings and 10 led sensors, in turn, provide 10-bit outputs. The bit pattern outputreads 1100011100.a) Sketch the encoder rings and led sensors circuit then discuss its workingprinciple and applications in robotic systems.b) Calculate the encoder resolution and the absolute angular position of the shaft.c) What the equivalent gray code for the same angular position of the shaft?
The outputs of four registers, A, B, C, D, H, L are connected through 8:1 line multiplexer to the input of a fifth register, X. Each register is 16 bits long. The required transfers are dictated by four timing variables, T0 through T3 as follows: T0 : X←A T1 : X←B T2 : X←C T3 : X←D The timing variables are mutually exclusive, which means that only one variable is equal to 1 at any given time, while the others are equal to 0. Draw a block diagram showing the hardware implementation of the register transfers. Include the connections necessary from the four timing variables to the selection inputs of the multiplexers and to the load input of register X.
Computer Science Draw schematic with transistors size for the the operation ((A+B)C)' , find the logical effort g on input A, B, C and parasitic delay p.
A c code to move stepper motors controlled by stepper drivers in two dimensions on pic16F877A and A c code to open and close sd card on pic16F877A
Please written by computer source Question 1 a. Tri-state logic is often used in digital design to resolve the conflict that arises when more than one output is connected. With the aid of a diagram, explain how this can be used in a digital design to share a single bus. b. Examine the following VHDL statements and draw a synthesised schematic for the corresponding design. c. Using concurrent statements only, (no process), describe a decoder in VHDL which satisfies the following conditions, and draw the High level RTL schematic for this design. 3 inputs (A, B, C) and 1 output (Z). The output is equal to 1 when either input A is equal to 1 or only input C is equal to 1. All signals are of type 'std_logic d. VHDL allows the designer to describe hardware using different language constructs. Although, these constructs might have the same, or similar, functionality, the result of the synthesis is quite different. One example is the if-else and the case constructs. Explain the difference…
Design and draw a circuit diagram for a multiplexer for 2 inputs, x0 and x1, and one control bit, c0. When the control bit is 0, then the circuit should give x0 as output. When the control bit is 1, the output should be x1. Design a multiplexer for 4 inputs, x0, x1, x2, and x3, and 2 control bits, c0 and c1. The output for the multiplexer should be xk, whenever k = c1c0.
Describe the significance of the ALU in handling matrix arithmetic for graphic processing units (GPUs).
CREATE A FSM STATE DIAGRAM USING THE FOLLOWING INFORMATION:The system has four states, which represent the current level of the elevator (inorder from highest level to lowest level): Entrance Floor (ground level), EmployeeParking (first underground level), Underground Parking 2 (one level below em-ployee parking), Underground Parking 3 (two levels below employee parking)•The system has two 1-bit inputs: Up (label: u), Down (label: d)•The system has one 2-bit output: Level (label: L or L1 and L0 for each individualbit, where index 1 indicates the MSB and index 0 the LSB) •If the Up button is pressed, the elevator goes to the level above. If the elevator isalready in the highest level, pressing the Up button will have no effect and will stayin the current level. In case the level above is the employee parking, the elevatorwill skip this level and go directly to the level above it.•If the Down button is pressed, the elevator goes to the level below. If the elevatoris already in…
Consider the ASM CHART. Design only the control logic of the system. Answer the following: Design the control with multiplexers, a register, and a decoder.