A Wind Energy Conversion System with the following data: Downward wind velocity:9 m/s Upward wind velocity :27 m/s Length of blade: 20 meters Efficiency of Gear system: 75% Efficiency of Generator: 85% Evaluate: Assume necessary data d. The Output power of Gear system. e. The Output power of Generator.

A Wind Energy Conversion System with the following data: Downward wind velocity:9 m/s Upward wind velocity :27 m/s Length of blade: 20 meters Efficiency of Gear system: 75% Efficiency of Generator: 85% Evaluate: Assume necessary data d. The Output power of Gear system. e. The Output power of Generator.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

For Problem 19.27 , determine the probability (assuming normal distribution) that a car would need engine maintenance between 70,000 and 90,000 kilometers.
A 731 KW diesel-engine power plant has the following data: fuel rate, 245 liters per hour at 22 C with a specific gravity of 0.922; coolant flow rate, 1135 liters/min, with inlet and outlet temperature of 25 C and 35 C, respectively; air temperature of 18 C at a volume flow rate of 5031 m°/hr; exhaust gas temperature of 400 C. If the engine is an 8-cylinder, 375 mm x 457 mm x 267 rpm and the generator efficiency is 93 %, conduct an engine heat balance based on the above data.
Dusty air at a fertilizer plant flows through a 70%-efficient cyclone and then through an ESP. The inlet air to the cyclone has a dust loading of 50 grains/cubic foot. in order to meet a control standard of 98.5% collection efficiency for the fertilizer plant as a whole, what is the allowable concentration of dust (in grains/cubic foot) in the air that exits from the ESP?
A spring-operated relief device must be sized for a pressure vessel containing an ideal hydrocarbon vapor. The controlling scenario has a mass discharge rate, W, of 20 kg/s. Assume a vessel Pmawp of 10 barg, no superimposed backpressure, a built-up backpressure equal to 10% of set pressure and process temp of 473K. A review of normal operating pressures concludes that a set pressure, Ps of 8 barg will be used. The vapor has a molecular wt. of 120, heat capacity ratio of 1.3 and is ideal z=1.0. Determine the orifice diameter
An IC engine built to generate power on the basis of constant volume combustion cycle is tested for its performance and the following data were noted. Time taken for 30 cc consumption of fuel by engine=50 seconds, Number of cylinders=1, Mean effective pressure=13 bar, Brake load on dynamometer=6kg, Brake drum radius=22 cm, Engine speed =2308 rpm, Stroke volume = 800 cc, Calorific value of fuel=44000kJ/kg, Specific gravity of fuel=0.7, Density of3standard fluid=1000kg/m , IP=40kW.a) Find if the engine used is a 2-stroke engine or 4-stroke engine?b) What is the percentage conversion of combustion heat to useful output power?c) What percent of the power generated inside the cylinder is transmitted as useful power output?d) If the swept volume is increased by 10%, what would be the change in power generatedinside the cylinder if the engine speed and mean effective pressure is assumed to remain the same as before?
Instruction: Show your solution. (Engineering Utilities 2) Problem: A compressor draws in 500 cubic feet per minute of air whose density is 0.079 pounds per cubic feet and discharges it with a density of 0.304 pounds per cubic feet. At the suction, pressure # 1 = 15 pounds per square inches and at the discharge, pressure # 2 = 80 pounds per square inches. The increase in internal energy is 33.8 Btu per pound of air, and the heat rejected from air by cooling is 13 Btu per pound of air. Determine the work done on the air in Btu per minute and in horsepower. (1Btu = 778.16 ft-lbf; 1hp = 42.4 Btu/min)
(a) A very important component of a system has a mean time between failures of 100 hr and a mean time to repair of 10 hr. Determine the inherent availability of the system. (b) If the equipment in Q7 (c i) above is required to meet an inherent availability requirement of 0.985 and a mean time between failures of 100 hr. Calculate the permissible mean time to repair and if the system as a mean of the time intervals between corrective maintenance actions of 900 hrs and the sum of the mean corrective maintenance time intervals including supply downtime and administrative down time of 10 hrs Determine the operational availability of the system
identifuy the limitations that exist within different types of water turbine
Evaluating internal combustion engine’s performance?in your own word
Show work for both subparts as it is a single problem.
Specific fuel consumption of a four-stroke internal combustion engine at a given rotational speed is 0.322 kg/kW-h value is minimum. Spindle power at this rotation rate is 123 kW, volumetric efficiency is 95% and air-fuel rate is 15. The number of rotations of this engine is calculated by subtracting 1.5 from the number of rotations giving the minimum specific fuel consumption. time, spindle power 162 kW, specific fuel consumption 0.394 kg/kW-h and volumetric efficiency 85%. a) Calculate the air-fuel ratio in this case. and By what percent has the efficiency of the engine changed?
The following data refer to a 12-cylinder, single-acting, two-stroke marine diesel engine:Speed: 150 rpmCylinder diameter: 0.8mStroke of piston: 1.2 mArea of indicator diagram: 5.5x 10-4 m2Length of diagram: 0.06 mSpring value: 147 MPa per mFind the net rate of work transfer from the gas to the piston in kW.