A horizontal L=1.2 m long mb=14 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 23° angle with horizontal. A 24 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of horizontal hinge force.

A horizontal L=1.2 m long mb=14 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 23° angle with horizontal. A 24 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of horizontal hinge force.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.4.5P: A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and...

See similar textbooks

Related questions

Q: A particle which moves with curvilinear motion has coordinates in millimeters which vary with the…

A: Introduction: Motion is usually linear in a straight line or rotational in a half or complete circle…

Q: The Mach no. of a fixed geometry inlet at overspeeded for starting mode (Ai= 0.13 m2, At= 0.095 m2

A: Inlet Area, Ai = 0.13 m2 Throat Area, At = 0.095 m2

Q: Water at 15°C is transported from a large open tank to the bottom of another open tank above. The…

A: Answer: The Reynolds number of the flow: Re = 12438705.2

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: AB = 1923.27 N AC = 264.57 N BC = -738.27 N

Q: Part A Determine the magnitude of the velocity of car B relative to car A. Express your answer to…

Q: The technician............... machine, but ............... no time. He wasn't very busy. to repair…

A: GIven

Q: A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter…

A: GIVEN DATA- m=585kg dm=20mm p=5mm Coefficient of friction =0.1 We have to find torque required to…

Q: The Milkin Aircraft Co. manufactures a turbojet engine that is placed in a plane having a weight of…

A: Given Data : Thrust(T)= 5200 lb Speed (v)= 600 mi/h

Q: (b) For the configuration shown below. Write the finite difference equation under steady state…

A: The finitie difference equation under the conditon of steady-state for the node (m,n) is given by,…

Q: A shaft is to have a semicircular grove machined around the circumference at a specified location.…

Q: A plate moving 10 cm/s to the right is 0.5 cm above a stagnant wall. The fluid between the plate and…

A: Introduction: Viscosity is a measure of a fluid's resistance to flow, which influences how it…

Q: The particle has a mass of 0.45 kg and is confined to move along the smooth horizontal slot due to…

A: Given: The mass of particle, m = 0.45 kg The angular acceleration of arm, α = 3 rad/s^2 The angular…

Q: 5) When is the tangential force greater than the normal force? A) Only at the very beginning B) in…

A: The normal force is just the frictional forces between two surfaces which is in contant. Tangential…

Q: Determine the expected Fanning friction factor for water at 28 degrees Celsius flowing through a…

Q: Q.3) Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Givenpower provided by pump to water P=20kWZ=45mhL=23m

Q: 1. Show the computation using P water ( HP) 2. Show the computation for Density of Air and Specific…

Q: escribe details of an engineering design process. How problem definition helps in i

Q: Q.1) Determine the convection heat transfer coefficient and the heat flux on the plate surface for…

Q: A batch of 10 cutting tools could produce 500 components while working at 50 rpm with a tool feed of…

A: Given data: N1=50 rpmf1=0.25 mm/revN2=80 rpmf2=0.25 mm/rev Need to determine the number of…

Q: 3-19 Consider a 1.2-m-high and 2-m-wide double-pane win- dow consisting of two 3-mm-thick layers of…

A: Find Steady rate of heat transfer

Q: Air at 20°C and 7 bar is contained in a rigid tank of 0.57 m3 volume capacity. The tank is provided…

A: Given data as per question P1=7 barT1=200CV1=0.57 m3

Q: There is an ambient temperature of 65°C with a temperature rating of the conductor as 75°C. What is…

A: Introduction

Q: Determine the expected Fanning friction factor for water at 28 degrees Celsius, flowing through a…

A: Give data as per the question The internal diameter of the tube =15 mm = 0.015 m velocity =0.3 m/s…

Q: The molecular weights of two components A and B of a gas mixture are 24 and 28 respectively. The…

A: Given: The molecular weight of component A, mA = 24 The molecular weight of component B, mB = 28 The…

Q: = 0.3m, r2 = 0.2m & operates under the following Q3/ A Francis turbine has runner radii: 1₁…

A: Francis Turbine is an inward radial flow reaction turbine with radial discharge in order to get exit…

Q: 3. The velocity of the flow () in a pipe is equal to 2gx 20 1+ 200f a. b. C. V= V = V = 2gx20 1+200/…

Q: The Mach no. of a fixed geometry inlet at overspeeded for starting mode (Ai= 0.13 m2, ,At= 0.095 m2)

A: Given data: Area at inlet, Ai = 0.13 m2 Area at throat, At = 0095 m2

Q: Learning Goal: A particle of mass M moves along a straight line with initial speed v₁. A force of…

Q: Based on the given equations for the bending moment M(x) applied to the shown beam, determine the…

Q: A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown below. The water flows through a…

Q: The velocity of flow after a normal shock wave when (Tx= 315 K, vx= 555 ms-1)

Q: The structure deflects a jet of water as shown in figure. The pressure at a is 550 kPa. Find the…

A: Introduction: If a plate, either moving or immovable, is put in the path of the jet, the jet will…

Q: Q.1) Determine the convection heat transfer coefficient and the heat flux on the plate surface for…

Q: Q1/ Select the right answer for the following question? 1) the kinematics of a particle happened…

A: 1-dimensional kinematics can be represented by various methods to represent the motion of objects…

Q: Reservoir engineers transfer a crude oil with at 30 °C, and 9 kPa, and 200 m³ volume to tank by…

Q: dryness fraction of the refrigerant at entry to

A: Given data; Specific enthalpy,h1=250 kJ/kgExit temperature enthalpy,h2=300 kJ/kgCOP= 3 Evaporator…

Q: 1. Specify the sizes of pipes (cast iron, schedule 40) and the size of the motor to be used for a…

A: Given Data: Flow rate of the pump, Q = 50 litres/sec = 0.05 m3/s Total static head, (z1 -z2) = 50 m…

Q: rotameter with fla nternal diameter of The diameter of the What is the mass fl

A: Introduction:

Q: The velocity of flow after a normal shock wave when (Tx= ,315 K, vx= 555 ms-1) 275.7 ms-1 O 396.1…

Q: Q.1) Determine the convection heat transfer coefficient and the heat flux on the plate surface for…

Q: 10.4 A steel thick cylinder of external diameter 150 mm has two strain gauges fixed externally, one…

Q: The steam from the nozzles of a single wheel impulse turbine is 600m/s and at 20degree to the plane…

A: Given Inlet velocity = 600 m/s Angle = 20o N = 3000 rpm Blade radius = 590 mm Exit velocity = 164…

Q: If the sloping wall is 4 m wide. Calculate the location and magnitude of the force due to the oil…

A: To find: Resultant force due to oil pressure, FR = ? The location of the above resultant force = ?

Q: A pump rated at 1800W is used to transfer water from an open tank to another tank. The surfaces of…

A: Given that: Electric power consumed by the pump = 1800 W Vertical distance between the two tanks =…

Q: At a given instant, the gear has the angular motion shown. (Figure 1) Figure @=6 rad/s a = 12 rad/s…

Q: A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and…

Q: 1. Oil with a density of 910 kg/m³ and viscosity of 0.0019 m²/s is pumped through a 150 mm diameter…

A: Given data: Density of oil = ρ = 910 kg/m3Viscosity of oil =µ = 0.0019 m2/sDiameter of pipe = D =…

Q: Four functions of a clutch

A: Clutch is defined as the machine element which is used to engage and disengage the driver and driven…

Q: t in an organic synthesis, orarily stored in drums fo

A: The management approach helps to understand management. There are many approaches to management that…

Q: vacuum gauge connected to a chamber reads 40 kPa. Atmospheric pressure at the ocation is 100 kPa.…

A: Given: Pvacuum = 40 kPa Patm = 100 kPa To find : Pabs

Question

Find the magnitude of horizontal hinge force.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

A wracking ball is suspended below two cables each at an angle with the horizontal. The left cable has tension T1 and angle 37 degrees with the horizontal. The right cable has tension T2 and angle 22 degrees with the horizontal. The Wracking ball has mass 180 kg.

Find the magnitude of tension T2.

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
A bar ABC revolves in a horizontal plane about a vertical axis at the midpoint C (see figure). The bar, which has a length 2L and crass-sectional area A, revolves at constant angular speed at. Each half of the bar (AC and BC) has a weight W, and supports a weight W2at its end. Derive the following formula for the elongation of one-half of the bar (that is. the elongation of either AC ar BC). =L223gEA(w1+3w2) in which E is t he modulus of elasticity of the material of the bar and g is the acceleration of gravity.
By what distance h does the cage shown in the figure move downward when the weight W is placed inside it? (See the figure.) Consider only the effects of the stretching of the cable, which has axial rigidity EA = 10,700 kN. The pulley at A has a diameter da= 300 mm and the pulley at B has a diameter dB= 150 mm. Also, the distance L1= 4.6 m, the distance L2=10.5 m, and the weight W = 22 kN. Note: When calculating the length of the cable. include the parts of the cable that go around the pulley sat A and B.
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
A hollow circular pipe (see figure} support s a load P that is uniformly distributed around a cap plate at the top of the lower pipe. The inner and outer diameters of the upper and lower parts of the pipe are d1= 50 mm, d2= 60 mm, rf3 = 57 mm, and d1= 64 mm, respectively. Pipe lengths are Lt= 2 m and L, = 3 m. Neglect the self-weight of the pipes. Assume that cap plate thickness is small compared to I, and E,. Let E = 110 MPa. (a) If the tensile stress in the upper part is d = 10.5 MPa. what is load PI Also, what are reactions ft, at the upper support and R-, at the lower support? What is the stress ar(MPa) in the lower part? (b) Find displacement S(mm) at the cap plate. Plot the axial force diagram (AFD) [Ar(.f)] and axial displacement diagram (ADD)[5(.t)]. (c) Add the uniformly distributed load q along the censorial axis of pipe segment 2. Find q (kN/m) so that It, = 0. Assume that load P from part (a) is also applied.
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
The L-shaped arm ABCD shown in the figure lies in a vertical plane and pivots about a horizontal pin at A. The arm has a constant cross-sectional area and total weight W. A vertical spring of stiffness k supports the arm at point B. (a) Obtain a formula for the elongation of the spring due to the weight of the arm. (b) Repeat part (a) if the pin support at A is moved to D.
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
Space frame A BCD is clamped at A, except it is Free to translate in the .v direction. There is also a roller support at D, which is normal to line CDE. A triangularly distributed Force with peak intensity q0 = 75 N/m acts along AB in the positive - direction. Forces Px= 60 N and Pz = = 45 N are applied at joint C, and a concentrated moment My = 120 N . m acts at the mid-span of member BC. (a) Find reactions at supports A and I). (b) Find internal stress resultants N. E’I T, and .11 at the mid-height of segment AB.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A round bar ABC of length 2L (see figure) rotates about an axis through the midpoint C with constant angular speed w (radians per second). The material of the bar has weight density y. (a) Derive a formula for the tensile stress a’ in the bar as a function of the distance x from the midpoint C. (b) What is the maximum tensile stress a max?