A yo-yo rests on the table and is free to roll. There is a friction between the yo-yo and the table characterized by a coefficient u. A string wrapped around the shaft is pulled with constant tension T at an angle O with the horizontal. a) Find T, and 0, for which the yo-yo slips without rolling. b) Describe the motion when O<0, and O>0,. I2

A yo-yo rests on the table and is free to roll. There is a friction between the yo-yo and the table characterized by a coefficient u. A string wrapped around the shaft is pulled with constant tension T at an angle O with the horizontal. a) Find T, and 0, for which the yo-yo slips without rolling. b) Describe the motion when O<0, and O>0,. I2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
The controlling force curve of a spring controlled governor is a straight line. The weight of each governor ball is 40 N and extreme radii of rotation are 10 cm and 17.5 cm. If the values of the controlling force at above radli are 205 N and 400 N respectively and friction of mechanism is equivalent to 2.5 N at each ball. Find The extreme equilibrium speeds of the governor. (1) The equilibrium speed and coefficienct of insensitiveness at a radius of 15 cm
A mono-cylinder engine has r = 0.3 m, l = 0.9 m, It has: crank mass m2 = 4.5 kg , crank rG2 = 0.4r, conrod mass m3 = 12 kg ,conrod rG3 = 0.3l from A, and piston m4 = 5 kg. The crank is rotating at constant speed ω =3000 rpm. The following equation is an approximation of the gas force over 180° of crank angle with Fgmax = 3000 N and β = 15º. we need to find the gas force, gas torque, and inertia force . Use approximate expressions in your calculation
A ring of mass m is attached to the spring and slides over the rod. Unextended length of the spring l0 and the spring coefficient is k. When the collar is at point C, it is released and between the collar and bar Since the coefficient of friction is μk; a) Find the velocity of the ring at points A and B using the Work-Energy method. b) Find the normal forces acting on the collar at points A and B.
A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 34.5° with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.870, and the log has an acceleration of 0.750 m/s2. Find the tension in the rope.
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
The 10 N cylinder moves in a friction tube. Spring constants are k1 = 150 N / m and k2 = 200 N / m. When the system is at rest, d = 0.5 m. The system rotates around a fixed z-axis. In the case where d = 0.12 m, what is the coefficient of friction for the cylinder to have a constant velocity of 9.825 m / s?
For the double slider mechanism shown in the following figure, the crank OA rotates at a uniform speed of 100 rad/s CW. we need to find the required torque for the crank, if two forces act at sliders B and C as shown in the figure. (P = 2KN, Q = 1KN). OA = 30 cm, AB = AC = 100 cm. mB = mC = 1 Kg. Neglect other links weights. The velocity of slip of slider B in m/s2 = Answer 1 Choose... The velocity of slip of slider C in m/s2 = Answer 2 Choose... The acceleration of slip of slider B in m/s2 = Answer 3 Choose... The acceleration of slip of slider C in m/s2 = Answer 4 Choose... The magnitude of required torque for the crank in N.m = Answer 5 Choose...
An object with a mass of 0.5 kg is released from a distance of 2 m, the spring coefficient k = 100 N / m and the object is in the same direction after impact. If it is known to rebound on the road throughout; a) What is the speed of the object at the moment before it hits the spring? b) Find the maximum compression and maximum spring force in the spring. c) Find the rebound height if e = 0.5. (Assume that the spring behaves linearly during deformation, when the object leaves the spring, the spring regains its initial length (L) and energy is conserved during compression.)
The mass of Block(A) in Fig. below is( 6 kg ).The coefficient of friction between the block and the surface on which it rests is (0.25) .The weight (w) is (12N) and the system is in Equilibrium.(a)Find the friction force exerted on Block( A).//(b) Find the maximum weight of (W) for which the system will remain in Equilibrium
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m attached to a 50-kg block in an incline (©=30°). With the spring initially at equilibrium position, the block was pushed 0.3 meters up the incline by a 50-N external force applied parallel to the path. The coefficient of kinetic friction is 0.30. d) How much work is done by the block (in Joules) on the spring? e) How much work is done by the applied push on the block? f) How much work is done by friction?
A 40 kg youth jumps upwards at 8 m/s from a height of 5 m and lands on a trampoline of height 1 m and stiffness 20 kN/m. The system is 95% efficient. find the final height of the youth when they reach maximum stretch of the trampoline.