Please only answer if you’re 100% sure PLEASE! Please show all the equations and STEPS to resolve this problem please • Resistor XV = 4.7 |I Resistor YA Resistor ZV = 2.3 I|V = 0.6 |Current (I) [A]Assume you have one resistor of each resistorshown in the graph available for use.Determine the required resistance for thesystem in units of ohms[2]Choose one correct resistor or resistorcombination that will meet the criteria asclosely as possible.List the resistor(s) and the resistorconfiguration (individual, parallel, or series) andthe resulting resistance for the configuration.(a) You want the resistor(s) to provideapproximately 620 watts[W]Voltage (V) [V] (a) You want the resistor(s) to provideapproximately 620 watts[W]of power when using a current of 20 amperes[A](b) You want the resistor(s) to provideapproximately 1700 watts[W]of power when using 95 volts[V]

Ohm's law gave a relation between the voltage and the current through the circuit. He described that…

(a) You want the resistor(s) to provide approximately 620 watts [W] of power when using a current of 20 amperes [A] (b) You want the resistor(s) to provide approximately 1700 watts [W] of power when using 95 volts [V]

(a) You want the resistor(s) to provide approximately 620 watts [W] of power when using a current of 20 amperes [A] (b) You want the resistor(s) to provide approximately 1700 watts [W] of power when using 95 volts [V]

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 94CP: Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is...

See similar textbooks

Related questions

Q: Given that the delivered power to a resistor is equal to P when the current flowing in the resistor…

A: Given data: Current I =3.2I0

Q: An experimenter accidentally touches a 240 V dc line. If his skin resistance is 10 000 Ω, what value…

A: Given data : Voltage (V) = 240 V Resistance (R) = 10000 Ohm

Q: Two copper wires of diameters 0.260 cm and 0.201 cm, respectively, are connected in parallel. What…

A: Given: Combined current (i)=18A first copper wire has diameter 0.260 cm second copper…

Q: The parallel combination of five cells, each with electromotive force of 1.5 V and internal…

A: Given values: Number of cells, n=5 Emf of each cell, ε=1.5 V Internal resistance, r=0.5 Ω External…

Q: Foolishly trying to fish a burning piece of bread from a toaster with a metal butter knife, a man…

A: Given: V = 120 V

Q: If the potential difference across a resistor is doubled: only the current is doubled both the…

Q: When does an incandescent lightbulb carry more current, (a) immediately after it is turned on and…

Q: A portion of Nichrome wire of radius 3.25 mm is to be used in winding a heating coil. If the coil…

A: The radius of the Nichrome wire, r=3.25 mm = 3.25×10-3 m The current through the coil, I=8.90 A The…

Q: The resistance of a carbon coil is 10.5 Ω at 60 0C. At what temperature will its resistance decrease…

A: Write the expression for the resistance.

Q: 18.0 V 5.00 2 8.00 12.0V I100 7.00 0 5.00 0 36.0 V

Q: The wiring in a house must be thick enough so it does notbecome so hot as to start a fire. What…

A: P = 1.5 W I = 35 A

Q: e2 =5V, as in the connected to Two balteries with el 3v and Crcuit in the figure, 21= 10 W,it IS…

Q: Considering the circuit shown below, determine the magnitude of the current in amperes 3 Ω + a b Μ…

Q: Given the current through a point to be i(t) = 7.69 cos( 1.47 t), in amperes, determine the total…

A: Given data The current through a point is it=7.69cos1.47t The time intervals are 3.95 s<t<5.13…

Q: Will current flow more easily through a thick wire or a thin wire of the same material, when…

Q: An electric jug kettle has a rating of 2kW at 240 V. If the resistance per unit length is 3 ohm…

A: Given,Rating of electric jug kettle is 2KW at 240Vso, current rating I=2KW240V=2000W240VI=8.333Aso,…

Q: Suppose that each headlight of a car uses 3 A and that the driver accidentally left the headlights…

A: The headlight of the car uses 3A Battery =12v To find the time taken for the battery

Q: Assuming a steady current flow through a switch, find the time required for a (a) 20 C to flow if…

A: Write the expression of current I with relation to time t and charge Q. Part (a) Write the given…

Q: A portion of Nichrome wire of radius 2.60 mm is to be used in winding a heating coil. If the coil…

Q: Find the power dissipated when: (a) a current of 5mA flows through a resistance of 20 kn (b) a…

Q: suppose that each headlight of your car uses a 3 A and that you accidentally left the headlights on.…

Q: For a given voltage, if resistance is doubled the current will. increase by a factor of 2 O decrease…

Q: Given that the delivered power to a resistor is equal to P when the current flowing in the resistor…

A: solution

Q: Given that the delivered power to a resistor is equal to P when the current flowing in the resistor…

A: Option c = 146.4 P is the answer

Q: - In a discharge tube, the number of protons drifting across any cross-section is 1-0 x 1018 per…

Q: Which of the following situations results in a conventional current that flows eastward? O A beam of…

A: Given Direction of conventional current is Eastward We have to choose the correct option from given…

Q: Given that the delivered power to a resistor is equal to P when the current flowing in the resistor…

A: Given , Power delivered to a resistor is P Current through resistor is I0…

Q: A 60 W fluorescent bulb has resistance of about 12 Ω when cold (30˚C) and 120 Ω when on (hot).…

A: Given that, A 60 W fluorescent bulb has resistance of about 12 Ω when cold (30˚C) and 120 Ω when on…

Q: Given that the delivered power to a resistor is equal to P when the current flowing in the resistor…

A: We have to use some basic formula here.

Q: For the circuit shown in Fig.a 20.0 Ω resistor is embedded in a large block of ice at 0.00°C, and…

A: The resistances 20 Ω, 10 Ω and 20 Ω are connected in parallel, The equivalent resistance when all…

Q: Find the current flowing through a copper wire of length 20cm, area of cross section 1mm2, when…

A: Given: The length of the wire is 20 cm. The area of the wire is 1 mm2. The potential difference is 4…

Q: A device (such as a light bulb) experiences a voltage drop of 4.0 V across it while a DC current of…

A: The power dissipated by the device will be the product of the voltage drop across it and the current…

Q: Given that the delivered power to a resistor is equal to P when the current flowing in the resistor…

Q: 2.2 Use Thevenin's theorem to find the current flowing in the 6 Q resistor shown in the Figure below…

A: From the question, it is given that- External voltage: V = 40 V R1=5ΩR2=4ΩRL=6Ω

Q: the current in all three resistors is equal, which of the following statements must be true?

Q: Nichrome wire of cross-sectional radius 0.795 mm is to be used in winding a heating coil. If the…

Q: Given that the delivered power to a resistor is equal to P when the cCurrent flowing in the resistor…

A: We know that P= I2 X R

Q: A cylindrical resistor is to be constructed so that it offers the same resistance whether the…

A: The length of the resistance in millimeter is 81.5 mm , in centimeters it is 8.15 cm

Q: If current I decreases to half its original and the associated resistance decreases to O one-fourth…

Q: Since placing both ammeter probes between a pair of components connected to each other in series…

A: To measure the current, the ammeter should be placed in series with components.

Q: Suppose that each headlight of a car uses 3 A and that the driver accidentally left the headlights…

A: Energy stored in battery is given by, E=VIt Here, V is voltage, I is current and t is time. Energy…

Q: Why can't the current flow uniformly (linear over time) when the capacitor is charging or…

A: Capacitor is like a bucket which is storing electrostatic energy , as a constant voltage or current…

Q: While taking photographs in Death Valley on a day when the temperature is 59.0°C, Bill Hiker finds…

A: The expression to calculate the current is given by, I'=IRiRf Here, Ri is the initial conductor…

Q: If a current of one- or two-tenths of an ampere were to flow into one of your hands and out the…

A: We know that, according to Ohm's law, current is directly proportional to the voltage across the…

Question

Please only answer if you’re 100% sure PLEASE! Please show all the equations and STEPS to resolve this problem please

• Resistor X
V = 4.7 |
I Resistor Y
A Resistor Z
V = 2.3 I|
V = 0.6 |
Current (I) [A]
Assume you have one resistor of each resistor
shown in the graph available for use.
Determine the required resistance for the
system in units of ohms
[2]
Choose one correct resistor or resistor
combination that will meet the criteria as
closely as possible.
List the resistor(s) and the resistor
configuration (individual, parallel, or series) and
the resulting resistance for the configuration.
(a) You want the resistor(s) to provide
approximately 620 watts
[W]
Voltage (V) [V]

(a) You want the resistor(s) to provide
approximately 620 watts
[W]
of power when using a current of 20 amperes
[A]
(b) You want the resistor(s) to provide
approximately 1700 watts
[W]
of power when using 95 volts
[V]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

If the drift velocity in a conductor is so small, then why does an auto battery influence the starter as soon as you turn the ignition switch?
Verify that alter a time of 10.0 ms, the current for the situation considered in Example 23.9 will be 0.183 A as stated.
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
The temperature in Philadelphia, PA can vary between 68.00F and 100.00F in one summer day. By what percentage will an aluminum wire’s resistance change during the day?
Why is it advisable to allow electric line to sag between poles? Is it possible for a ship to use the internal energy of seawater to operate itsengine? Explain.
Would your headlights dim when you start your car’s engine if the wires in your automobile were superconductors? (Do not neglect the battery’s internalresistance.) Explain.
Using the results of the above example on Example 20.3, find the drift velocity in a copper wire of twice the diameter and carrying 20.0A.
Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is closed? (b) What is die current through resistor R2 when the capacitor is fully charged, long after die switch is closed? (c) What happens if the switch is opened after it has been closed for some rime? (d) If the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor R1 reaches half of its initial value?
Integrated Concepts If you wish to take a picture of a bullet traveling at 500 m/s, then a very brief flash of light produced by an RC discharge through a flash tube can limit blurring. Assuming 1.00 mm of motion during one RC constant is acceptable, and given that the flash is driven by a 600F capacitor, what is the resistance in the flash tube?
Integrated Concepts Use the ECG in Figure 20.34 to determine the heart rate in beats per minute assuming a constant time between beats. Figure 20.34 A lead II ECG with corresponding arterial blood pressure. The QRS complex is created by the depolarization and contraction of the ventricles and is followed shortly by the maximum or systolic blood pressure. See text for further description.
In this problem, you will verify statements made at the end of the power losses for Example 20.10. (a) What current is needed to transmit 100 MW of power at a voltage of 25.0 kV? (b) Find the power loss in a 1.00 transmission line. (c) What percent loss does this represent?
How would you go about improving the determination of the electrical resistance of a given material in resistor color coding?