A. calculate the volume of standardized 0.01 M KMNO4(aq). needed to completely react with ~0.125 g of the solution of potassium ferrioxalate 1M. I don't know if you just need the info but , 6 mL of 6 M sulfuric acid, and 1 mL of concentrated H3PO4(aq) will be added with 0.155 g of the solution of potassium ferrioxalate 1M in the flask, and the the volume of standard sodium hydroxide solution (~0.010 M) is what will be added to the buret and we need to figure out volume of standard sodium hydroxide solution to completely react with ~0.125 g of the solution of potassium ferrioxalate 1M.

A. calculate the volume of standardized 0.01 M KMNO4(aq). needed to completely react with ~0.125 g of the solution of potassium ferrioxalate 1M. I don't know if you just need the info but , 6 mL of 6 M sulfuric acid, and 1 mL of concentrated H3PO4(aq) will be added with 0.155 g of the solution of potassium ferrioxalate 1M in the flask, and the the volume of standard sodium hydroxide solution (~0.010 M) is what will be added to the buret and we need to figure out volume of standard sodium hydroxide solution to completely react with ~0.125 g of the solution of potassium ferrioxalate 1M.

Chemistry: Principles and Reactions

8th Edition

ISBN:9781305079373

Author:William L. Masterton, Cecile N. Hurley

Publisher:William L. Masterton, Cecile N. Hurley

Chapter10: Solutions

Section: Chapter Questions

Problem 65QAP: Twenty-five milliliters of a solution (d=1.107g/mL)containing 15.25% by mass of sulfuric acid is...

See similar textbooks

Similar questions

Twenty-five milliliters of a solution (d=1.107g/mL)containing 15.25% by mass of sulfuric acid is added to 50.0 mL of 2.45 M barium chloride. (a) What is the expected precipitate? (b) How many grams of precipitate are obtained? (c) What is the chloride concentration after precipitation is complete?
A mountain lake that is 4.0 km × 6.0 km with an average depth of 75 m has an H+(aq) concentration of 1.3 × 10−6 M. Calculate the mass of calcium carbonate that would have to be added to the lake to change the H+(aq) concentration to 6.3 × 10−8 M. Assume that all the carbonate is converted to carbon dioxide, which bubbles out of the solution.
Consider the equation G = -nF. What are the four terms in this equation? Why does a minus sign appear in the equation? What does the superscript o indicate?
When jump-starting a car with a dead battery, the ground jumper should be attached to a remote part of the engine block. Why?
68. Aluminum ion may be precipitated from aqueous solution by addition of hydroxide ion, forming Al(OH)3. A large excess of hydroxide ion must not be added, however, because the precipitate of Al(OH)3 will redissolve as a soluble compound containing aluminum ions and hydroxide ions begins to form. How many grains of solid NaOH should be added to 10.0 mL of 0.250 M A1Cl3 to just precipitate all the aluminum?
A sample of solid calcium hydroxide, Ca(OH)2, is allowed to stand in water until a saturated solution is formed. A titration of 75.00 mL of this solution with 5.00102M HCl requires 36.6 mL of the acid to reach the end point. Ca(OH)2(aq)+2HCl(aq)CaCl2(aq)+2H2O(l) What is the molarity?
Rei and Akari, two vinegar enthusiasts, are each tasked to determine the aceticacid content of their respective vinegar concoctions by titration. First, a 1M-labeled KOH solution was standardized against the KHP (MW = 204.22 g/mol)standard that is 99.4% pure. In the process, 0.540 g KHP was found to require2.80 mL of the KOH solution to completely react up to the phenolphthaleinendpoint. Then, Rei and Akari both prepared their samples by taking 10.0-mLaliquots of each vinegar and diluting them to 25.0 mL. Using the same titrant andindicator, Rei’s vinegar required 18.60 mL of the standardized titrant to reach theendpoint, while Akari’s vinegar required 16.50 mL of the same titrant to reach thesame endpoint. What is the exact concentration of the KOH titrant in molarity? What is the balanced chemical equation between the analyte and the titrant? What is the color transition (color X color Y) expected throughout thecourse of titration? What is the acetic acid concentration of Rei’s and…
25 mL of a bleach (NaOCl) sample is diluted to 500 mL. An excessive amount of KI is added to the 20 mL solution taken from here, and the released I2 is titrated with 35.5 mL of 0.0409 M NaS2O3. Accordingly, calculate the percent by volume of NaOCl in the sample (MaNaOC: 74.4 g/mol)A. 10.50%B. 15.75%C. 5.25%D. 20.85%
A solution with a volume of 500.0 mL contained a mixture of SO3 2- and S2O3 2-. A 100.0 mL portion of the solution was found to react with 80.00 mL of 0.0500 M 2CrO4 2- in a basic solution to give CrO2 -. The only sulfur-containing product was SO4 2-. After the reaction, the solution was treated with excess 0.200 M BaCl2 solution, which precipitated BaSO4. This solid was filtered from the solution, dried, and found to weigh 0.9336 g. A. Write down the reaction that occur B. Explain in detail how you can determine the molar concentrations of SO3 2- and S2O3 2- in the original solution.
Mark and John, two vinegar enthusiasts, are each tasked to determine the acetic acid content of their respective vinegar concoctions by titration. First, a 1 M-labeled KOH solution was standardized against the KHP (MW = 204.22 g/mol) standard that is 99.4% pure. In the process, 0.540 g KHP was found to require 2.80 mL of the KOH solution to completely react up to the phenolphthalein endpoint. Then, Mark and John both prepared their samples by taking 10.0-mL aliquots of each vinegar and diluting them to 25.0 mL. Using the same titrant and indicator, Mark’s vinegar required 18.60 mL of the standardized titrant to reach the endpoint, while John’s vinegar required 16.50 mL of the same titrant to reach the same endpoint. Question: What is the acetic acid concentration of Mark’s and John’s vinegar in molarity given that the Concentration of KOH is 9386 M?