a. determine the design moment that the beam will carry in kN-m at the midspan.b. determine the required steel area in mm^2c. determine the number of 16mm diameter bars A 350mm x 600 mm beam is carrying asuperimposed dead load of 25 kN/mand superimposed live load 40 kN/m allover the span of 5 m. The beam isunrestrained. The concrete to be usedhas strength of 27.6 MPa. The mainreinforcement has yield strength of 415MPa. Use steel cover of 70 mm.

The values given in the question are as follows: Width of beam(b)=350 mm Depth of beam(D)=600 mm…

Answered: a. determine the design moment that the…

a. determine the design moment that the beam will carry in kN-m at the midspan. b. determine the required steel area in mm^2 c. determine the number of 16mm diameter bars

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam has a width of 285 mm and an effective depth of 520mm. It is reinforced with 4 – 36 mm ø bars having fy = 430 MPa. If he compressivestrength of the concrete is 28MPa, find the following a. Location of the neutral axis from the top of the beam.b. Stress of the steel.c. Ultimate capacity of the beam?
A rectangular beam 250 mm wide, 500 mm deep is reinforced at thebottom with 4-20-mm-diameter bars and at the top with 2-16-mmbars. Concrete cover to bar centroid at the top is 80 mm and at thebottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yieldstrength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 2. Determine the design moment capacity of the beam in positivebending. = [m] kN∙m (whole number)
A rectangular beam 250 mm wide, 500 mm deep is reinforced at thebottom with 4-20-mm-diameter bars and at the top with 2-16-mmbars. Concrete cover to bar centroid at the top is 80 mm and at thebottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yieldstrength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 3. Determine the design moment capacity of the beam in negativebending. = [n] kN∙m (whole number)
A rectangular column of 400mm x 600mm is subjected to an axial load of 500 kN and a moment of 30 kNm about its major axis. The grade of concrete used is M30 and the steel used is Fe415. Determine the axial load carrying capacity of the column using the limit state method.
1. A rectangular reinforced concrete beam has a length of 7.5 – 10.5 m. It is supported with a hinged at one end and a roller 2m from the other end. The width of beam is 350 mm and the overall depth is 550 mm. The beam is reinforced with 5D25 tensionreinforcement and 2D25 compression reinforcement located at 60 mm from the outermostfiber of the beam. The concrete strength fc = 28 MPa and steel yield fy= 390 MPa. Determinethe following:a. Sketch the beam and its cross sectionb. Stress in the compression steel.c. Moment capacity of the beam.d. Factored uniform load throughout the entire span of the beam that could carry.
A reinforced concrete T-beam carries a uniformly distributed super-load on a simply supported span of 8 m. The stresses in the steel and concrete are not to exceed 125 MN/m2 and 7 MN/m2, respectively. The modular ratio is 15, and the density of concrete is 2400 kg/m3. Determine the permissible super-load. (Nottingham) Note the answer in this problem is :144KN (show the solution)
Check the capacity of the plain concrete beam having span of 20ft. A load of 2.0 kip/ft is applied on beam. The beam has width = 12” and depth = 20”. Concrete compressive strength (fc′) = 3 ksi
A beam has a flange width of 810mm and a slab thickness of 50mm. The width of the web section is 300mm and it has an effective depth of 550mm. It is reinforced at the bottom with a steel area of 1750mm2. fc’ = 20MPa, fy = 400MPa. The magnitude of the compressive force of concrete is ____kN
A pretensioned beam is to carry a superimposed dead load of 600 plf and live load of 1,200 plf on a 55-ft simple span. A symmetrical I-section with be used. Flange thickness k_{f} = 0.2h and web width b - = 0.4b The member will be prestressed using Grade 270 strands. Time-dependent losses at 20 percent of P, Normal density concrete will be used, with f_{c}' = 5000 psi and -3,000 psi. (a) Using straight strands, find the required concrete dimensions prestress force, and eccentricity. Select an appropriate number and size of tendons, and show by sketch their placement in the section. (b) Revise the design of part (a) using tendons deflected at the third points of the span, with eccentricity reduced in zero at the supports (c) Comment on your results in both cases, ACI stress are to be applied. You may assume that deflections are not critical, and that a tele stress of 12 is permissible at full service load
A rectangular concrete beam has a width of 300 mm and an effective depth of 550 mm. The beam is simply supported over a span of 6 m and is used to carry a uniform dead load of 25 KN/m and a uniform live load of 40 kN/m. Assume fic= 21 MPa and fx = 312 MPa. Compression reinforcement if necessary shall be placed at a depth of 80 mm from the extreme compression concrete. Which of the following most nearly gives the maximum tension steel area for singly reinforced beam? A. 3810.50 mm2 B. 3959.17 mm2 C. 4223.11 mm2 D. 4751.04 mm2
A rectangular reinforced concrete beam has a length of 14 m is simply supported atboth ends. The width of beam is 350mm and the overall depth is 550 mm. Determine the area of the steel reinforcements if the beam is to carry a DL = 15kN/m and LL =18kN/m. The concrete strength fc = 25 and steel yield fy = 400 ��. Use 60 mm concretecover.
A rectangular reinforced concrete beam has a length of 7.5 m. It is supported with a hinged at one end and a roller 2m from the other end. The width of beam is 350 mm and the overall depth is 550 mm. The beam is reinforced with 5D25 tensionreinforcement and 2D25 compression reinforcement located at 60 mm from the outermostfiber of the beam. The concrete strength fc = 28 MPa and steel yield fy= 390 MPa. Determinethe following:a. Sketch the beam and its cross sectionb. Stress in the compression steel.c. Moment capacity of the beam.d. Factored uniform load throughout the entire span of the beam that could carry.