A. V When a jet strikes an inclined fixed plate, as shown, it breaks into two jets at 1 and 2 of equal velocity V but unequal areas. The reason is that for frictionless flow the fluid can exert no tangential force Fr on the plate. The condition Ft=0 enables us to solve for Ft-0. Perform this P. Q. A. V analysis, and find the ratio Q/Q. F, 0 A2.V

A. V When a jet strikes an inclined fixed plate, as shown, it breaks into two jets at 1 and 2 of equal velocity V but unequal areas. The reason is that for frictionless flow the fluid can exert no tangential force Fr on the plate. The condition Ft=0 enables us to solve for Ft-0. Perform this P. Q. A. V analysis, and find the ratio Q/Q. F, 0 A2.V

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 20 °C water jet strikes a vane mounted on a tank withfrictionless wheels, as in Fig. P3.61. The jet turns and fallsinto the tank without spilling out. If θ =30 ° , evaluate thehorizontal force F required to hold the tank stationary.
In Fig. water exits from a nozzle into atmosphericthe pressure of 101 kPa. If the exit velocity is V 2 = 8 m/s andfriction is neglected, what is the axial fl ange force requiredto keep the nozzle attached to pipe 1?( a ) 11 N, ( b ) 56 N, ( c ) 83 N, ( d ) 123 N, ( e ) 110 N
Water at 20 ° C flows down through a vertical, 6-cm diametertube at 300 gal/min, as in Fig. P3.74. The flowthen turns horizontally and exits through a 90 ° radial ductsegment 1 cm thick, as shown. If the radial outflow is uniformand steady, estimate the forces ( F x , F y , F z ) required tosupport this system against fluid momentum changes.
Consider Fig. P3.36 as a general problem for analysis of amixing ejector pump. If all conditions ( p , ρ , V ) are knownat sections 1 and 2 and if the wall friction is negligible,derive formulas for estimating ( a ) V 3 and ( b ) p 3 .
A fl uid jet of diameter D 1 enters a cascade of movingblades at absolute velocity V 1 and angle β 1 , and it leaves atabsolute velocity V 2 and angle β 2 , as in Fig. P3.78. Theblades move at velocity u . Derive a formula for the powerP delivered to the blades as a function of these parameters.
Water at 20 ° C fl ows steadily through the tank in Fig.P3.101. Known conditions are D 1 = 8 cm, V 1 = 6 m/s, andD 2 = 4 cm. A rightward force F = 70 N is required to keepthe tank fi xed. ( a ) What is the velocity leaving section 2?( b ) If the tank cross section is 1.2 m 2 , how fast is the watersurface h ( t ) rising or falling?
A uniform water stream, U∞ = 20 m/s and ρ = 998 kg/m3,combines with a source at the origin to form a half-body. At(x, y) = (0, 1.2 m), the pressure is 12.5 kPa less than p∞. (a) Isthis point outside the body? Estimate (b) the appropriatesource strength m and (c) the pressure at the nose of the body.
In Fig. water exits from a nozzle into atmosphericpressure of 101 kPa. If the fl ow rate is 160 gal/min and frictionis neglected, what is the gage pressure at section 1?( a ) 1.4 kPa, ( b ) 32 kPa, ( c ) 43 kPa, ( d ) 29 kPa, ( e ) 123 kPa
A water jet 7.6 cm diameter strikes concrete (SG=2.3) slab which rests freely on a lever floor. If the slab is 30.5 cm wide into a paper, calculate the jet velocity which will just begin to tip the slab over.
A 250mm diameter horizontal jet discharging at 491 L/s impinges on a vertical flat plate. Which of the following most nearly gives the force exerted by the jet on the plate if the plate moves at 2m/s in the same direction as the jet?
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.