a.1) In a certain UJT, 'B1 = 2.5 KQ and r'B2 = 4 kQ. What is the intrinsic standoff ratio? a.2) Determine the peak-point voltage for the UJT in problem a.1 if VBB = 15 V. a.3) Find the range of values of R₁ in Figure 2-10 that will ensure proper turn-on and turn-off of the UJT. n = 0.68, Vv = 0.8 V, /v = 15 mA, Ip = 10 μA, and Vp = 10 V. a.4) At what anode voltage (VA) will each PUT in Figure 2-11 begin to conduct? FIGURE 2-10

a.1) In a certain UJT, 'B1 = 2.5 KQ and r'B2 = 4 kQ. What is the intrinsic standoff ratio? a.2) Determine the peak-point voltage for the UJT in problem a.1 if VBB = 15 V. a.3) Find the range of values of R₁ in Figure 2-10 that will ensure proper turn-on and turn-off of the UJT. n = 0.68, Vv = 0.8 V, /v = 15 mA, Ip = 10 μA, and Vp = 10 V. a.4) At what anode voltage (VA) will each PUT in Figure 2-11 begin to conduct? FIGURE 2-10

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the Buck - Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: in the voltage range of [AB] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (UF) 5) Load current lload) value: [KS] (Amps) current range The lowest Linductance value that can keep the DC-DC converter in continuous current condition under The lowest ripple (AIL) amount of the current passing through the coil (L) is given below in Amps. Which option do you see? A = 40 Volts B = 80 Volts M = 25kHz F = 55 Volts K = 10 Amps S = 25 Amps
NOTE: FOR ALL CIRCUITS SHOWN IN THIS QUIZ ASSUME THAT: β= 100 (for all transistors) ; Early voltage equal to infinity. 1.- In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R equal to 100 Ohms and C equal to 1000 microfarads. The diodes are silicon (Vd = 0.7 volts) and the Zener diode is 15 volts. Determine:a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2
Q3: For the circuit shown in Figure 2, find the following:1. Describe the function of the circuit in terms of simple of semiconductor behavior.2. Evaluate the output voltage vo, assuming vs is 10 Sine (200t) mV, RE1 =100 Ω,and RE2 =900 Ω. The bypass capacitor (CE) is in parallel with RE2. 3. explain the characteristics of the amplifier.
A loaded zener regulator has a VZ of 11 V with IZ equal to 23 mA, with IZK equal to 0.25 mA, ZZ equal to 8 Ω and a PD (max) equal to 1 W. The value of the resistance R is equal to 32 Ω. Determine the values of the output voltage with IZK and IZM. Get the value of the minimum load resistance that can be used to keep the zener diode regulating.
For the JFET shown in Figure, Determine the minimum value of VDD required to put the device in the constant-current region of operation when VGS = 0 V. where VGS(off) = - 4 and IDSS = 42mA
2b) A regulator curcuit needs to be designed with an input power supply which has a nominal value of V_PS=20 V and can vary by ± %25 and nominal output voltage of 10 volts. For this purpose a zener diode is employed with specifications given; power rating of 1 W, 10V drop at Iz=25 mA, output load current is to vary between I(subscript L)=0-20 mA and zener resistance of r_Z=5Ω i) If the minimum Zener current is to be I_Z=5 mA, determine the required R_S ii) Determine the maximum variation in output voltage iii) Determine the regulation percent
Q3:Choose One of the following: : (A)In common emmiter voltage divider bias of BJT, Vcc = 25V; R1= 10 k ohm; R2, = 2.2 k ohm ;Rc = 3.6 k ohm and RE = 1 k ohm.Determain Vec at ß = 120.using Exact analysis Draw the equvelent circuit inaddition the DC load line curve . (B)For self bais(Emitter resistace bais) of BJT,Vcc= 22 V, lb = 45macroA, a = 0.99, RE = 1 k ohm. Determain VCe Draw the equvelent circuit inaddition to DC load line curve.
‏( b ) For the Junction Field Effect Transistor ( JFET ) shown in Figure Q1 ( b ) below , given that maximum current Ipss = 10 mA , pinch - off voltage Vp = -5 V , R D= 2 ka , source voltage and resistance are VDD= 12 V and Rs = 5 kn , respectively , solve to determine following (i) The quiescent voltage between the gate and source VGSQ . (ii) The quiescent drain current IDQ
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
Fig. 2 shows a single-phase fully controlled rectifier driving a heating element that has a resistance of 10 Ω. The supply voltage, Vs, is 230 Vac at 50 Hz and αf = 30 degrees. Answer the following: Draw a fully labelled waveform diagram showing the output voltage and current with respect to the Vs and the firing angle, αf. Use the waveform to develop an expression for the average output current and voltage Use this expression to calculate the average output current and voltage. What changes (if any) would be observed in Vo if the source Vs was taken from a transformer with a very high inductance?
To study the input and output characteristics of a BJT in Common Emitter(CE) Configuration and plot it on graph.lab report Input Characteristics: V CE = 5V V CE = 10V V BB (volts) V BE (volts) I B (µA) V BE (volts) I B (µA) Output Characteristics: I B = 431μA (VBB=5V) I B = 930μA (VBB=10V) V CC (volts) V CE (volts) I C (mA)
Q23.For the circuit shown in the figure , find the operating point. What is the stability factor of the circuit ? Given that β = 50 and VBE = 0.7V.