Answered: An inductor coil connected across a 120…

An inductor coil connected across a 120 V, 60 Hz supply takes 10 A. The resistance of the inductor coil can be neglected. Determine: the inductive reactance of the coil. the inductance of the coil

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 3PP: The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the...

See similar textbooks

Related questions

Q: -give two different constellations for a 32 QAM system then calculate the average of the transmitted…

A: According to the question, we need to show two different types of types of constellation diagram of…

Q: A 3-phase transmission line operating at 10 kV has a resistance of 192. The percentage resistance of…

A: Given, A 3-phase transmission line with, Rated line voltage, V = 10 kV Resistance, R=1 Ω Base kVA =…

Q: 2MA I₁ = V₁ - Du 3k Va-V₂ = 3V A mv Node A KCL ZMA + O- VD in вка 3k Eg #1 + i, 30 mm- Given - super…

Q: Simplify the following functions, and implement them with two level NOR gate circuits: F (x, y, z)=[…

A: Given function, Fx,y,z=x+yx'+z' To find: Simplify the following functions, and implement them with…

Q: What is the voltage drop across the 2Ω resistor? 10 Ω 122 V Select one: a. Ο • b. 12 c. 18 d. 22 e.…

A: Given, The circuit is,

Q: If two capacitors of 15 and 20 microfarads are connected in series to a 600 volt supply, find (1)…

Q: 24 The following data were obtained on a 20 kVA, 50 Hz, 2000/200 V Transformer: SCT: 60 V, 10 A, 300…

A: Given data: Vsc=60 VIsc= 10 APsc=300 W Short circuit test is conducted on HV side. Reh=PscIsc2…

Q: Example -Determine the unknown Voltage and current for each not work of T-=12 MA

Q: 18 Given a 100 kVA, 50 Hz power transformer. The maximum efficiency of the transformer is 98.0 %…

Q: If reflection coefficient for voltage be 0.6, the voltage standing wave ratio (VSWR) is?

A: Given, Reflection coefficient for voltage, Γ=0.6

Q: PRACTICE 7.9 If vc (t) = 4 cos 105t V in the circuit in Fig. 7.26, find v¸ (t). Ans: -2.4 cos 10ºt…

Q: For e(t) = -3t (a) Express E*(s) as a series. (b) Express E*(s) in closed form. (c) Express E*(s) as…

A: When a binomial is raised to a number, the binomial expansion formulae are employed to determine the…

Q: Design a 18 person voter system using 4 bit parallel adder(s) only. Use a minimum number of…

A: Given components: 4-bit parallel adders To design: An 18-person voter system using a minimum…

Q: Calculate the IDS current for an NMOS transistor. Assume that the transistor has W = 50 μm and L = 3…

A: Given: Aspect ratio=WL=50 μm3 μm=503 Process transconductance parameter K'n=150 μAV2 Gate Voltage…

Q: The following data are obtained for 7.5 hp, 28A, 4-pole, 208V, 60Hz, Y-connected stator squirrel…

A: By using rotor bars to interact with the EMF of the stator, squirrel cage motors optimise…

Q: Simplify the Boolean function F(w, x, y, z)=Σ(4, 5, 6, 7, 12) with don’t-care function d(w, x, y,…

A: from given function construct K map and simplify the function.

Q: One cycle of a square wave signal observed on an oscilloscope is found to occupy 6 cm at a scale…

A: Given: One cycle of a square wave occupy 6 cm. Scale setting is 30 μscm.

Q: A 500 kVA, 6.6 kV star connected alternator has a synchronous reactance of 1.0 2 per phase and…

Q: 10. When there is 12 mA of current through a 1.2 kn resistor, the voltage across the resistor is

Q: series circuit containing a noninductive resistance of 3 Ω and a coil is connected to a 120 V, 60 Hz…

Q: 3. Consider the closed loop system given below. r(t) e(t) G(S) G(S) = K(S+1) S(S+ 2)(S + 3) y(t) a)…

Q: A PN-junction diode has a reverse saturation current rating of 20nA at 32C, if the forward voltage…

A: Given data, Reverse saturation Current IS=20 nA=20×10-9 A Forward Voltage drop VD=0.5 V

Q: A capacitor of 4.56 uF capacitance is connected to a d.c. source through a resis tance of 1 megaohm.…

A: We have a capacitor which is connected to a D.C source through resistance . We have been asked to…

Q: A power transformer is joined in star-delta. Its line voltage ratio is 66 kV/11 kV. The current…

Q: Calculate the equivalent resistance in the given circuit below: R1 11.6 ohms; R2 = 27.6 ohms; R3 =…

A: Given, The circuit is, Value of resistors are, R1=11.6 Ω,R2=27.6 Ω,R3=7.36 Ω,R4=7.64 Ω.

Q: choose the correct expression for A + A B C : °A + Вс ОB+A C O B + AC C+ AB

A: Given logic expression, F=A+A.B.C

Q: A 5 x 4.0 cm² laminated magnetic core has a flux of 5 mWb. Assuming a stacking factor of 0.8, the…

A: Given data: AreaA=5×4 cm2 =20 cm2fluxϕ=5 mWb =5×10-3 Wbstacking factor=0.8…

Q: Calculate the theoretical barrier height, built-in potential barrier and Schottky barrier width in a…

A: SOLUTION Given--> Si/Cr Junction Diode…

Q: Two signals m(t) and m₂(t) both band limited to 5 KHz are to be transmitted simultaneously over a…

A: Given:

Q: Define the measured period in which the voltage drops to 63% of the peak-to-peak output voltage.…

A: Given: Define the measured period in which the voltage drops to 63% of the peak-to-peak output…

Q: An information signal of 3cos(2m10¹t) is given to 3 bit PCM system. Sampling rate is twice of the…

A: Given data: Message signal expression, 3cos(2πm104t) number of encoder bits used per sample, n = 3…

Q: What is the name of the wires that connect the memory?

A: Memory: Memory serves as the computer's electrical storage facility for the instructions and data…

Q: Evaluate both sides divergence Theorem c/m² D = 2xy ay + x² azt and the rectangular Parallele piped…

A: Please comment if you need any clarification. If you find my answer useful please put thumbs up.…

Q: 21) State FIVE of the followings: 1- Discriminator circuit 5- Sampling theory 2-TDM 6- Nyquist rate…

A: Since you have posted a question with multiple subparts, we will solve first three subparts for you.…

Q: Express the complement of the following functions in sum-of-minterms form: F ( x , y , z ) = Π ( 3 ,…

A: Given function:- FX,Y,Z=π3,5,7 We have to complement the given function in sum-of-minterms.

Q: How much energy is imparted to an electron as it flows through a 9 V battery from the positive to…

A: Given: Electron flows through potential difference of ∆V=9 V.

Q: A d.c. series generator supplies the load of 5 kW at 250 volts. The armature resistance and series…

A: Solution: Given data ; d.c. series generator ; output =5 KW , V =250 V, armature resistance Ra=1 Ω,…

Q: What semiconductor materials would be more suitable for a single junction pv device for ground or…

A: GIVEN: Graph between normalized absorbance and wavelength FIND: Based on data, suggest a…

Q: The three loads in are fed from a line having a series impedance 0.01 + j0.08 , as shown in Fig.…

Q: The characteristics S¹ + 2s³+6s²+4s+1 = 0 Set up the Routh Table and determine the stability of the…

Q: 10V 5 4 12 V 8 1 Determine the value of the current passing through a resistance of 8 2 in the…

Q: 12 With a counter 10 lights willI be controlled. At the first clock pulse all lights will be ON (1).…

A: Given data: A counter 10 light will be controller. The counter is mode 10 counter.

Q: 72. In 132 kV system, the phase to ground capacitance is 0.01 µF and inductance is 6H. The voltage…

A: Given, Phase to ground capacitance, C=0.01 μF. Inductance, L=6 H. Magnetizing current, I=10 A.

Q: on 9 What is the modulation index for AM waveform with Vmax = 8.4 V & Vmin = 4.7 V? 0.28

Q: Please show 7 detailed Solution on this Part, and how it become That answer.

Q: In an induction motor, if the rotor is locked, then the rotor frequency of induction motor will be:…

A: Given: In the induction motor, the rotor is locked.

Q: Find the attached file.

Q: Find the voltage Vag in the circuit shown in Fig. 2.27. 10 v 10 Ω 20 Ω A 30 Ω 40 Ω

Q: find F.T the? f(t) = u(t) cos wot let u(t) = TS (W) + J W coswot = πTES (W_Wo +8 (W+wo)

Q: 8 The EMF induced in the secondary winding of a 50 Hz single-phase transformer having 500 turns on…

A: Given: The EMF induced in the secondary winding, E2=13.2 kV Frequency, f = 50 Hz Number of turns on…

Question

An inductor coil connected across a 120 V, 60 Hz supply takes 10 A. The resistance of the inductor coil can be neglected. Determine:
1. the inductive reactance of the coil.
2. the inductance of the coil

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the inductor, EL, is 104 V, and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. ETITZ20VAPFER78VIRRPEL104VILXLVARsLL
The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the power factor is 62.5%. The resistor has a voltage drop of 14.993 V, the inductor has an inductive reactance of 60 , and the capacitor has a capacitive reactance of 45 . ETITZVA29.985PF62.5%ER14.993VIRRPELILXL60VARsLLECICXC45VARsCC
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
Which of the following is the capacitance of two 20-microfarad running capacitors connected in parallel? 10 microfarad 20 microfarad 30 microfarad 40 microfarad
Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
An inductive coil of resistance 15 ohms and inductance 0.2H is connected in parallel with a 100 micro farad capacitor to a variable frequency supply. Find the frequency at which the total current taken is in phase with the supply voltage. What is this value of this current if the voltage is 200v. Draw a phase diagram
A coil having a 240V source has a current of 10.5 A when the frequency is set to 60 Hz. When the frequency is changed to 30 Hz, the resulting current is now 14.3 A. Find the inductance, L, of the coil (in mH).
An impedance coil is connected in series with a capacitor across a 220 V, 60 Hz acsupply. The circuit is designed such that the voltage across the impedance coil and thecapacitor are numerically equal. If this circuit operates at 0.866025403 leading powerfactor, determine the apparent power of the coil when the circuit current is 1 A. ASAP
a coil with a resistance of 25 Ω and an inductance of 75 mH is available, if a capacitor of unknown capacitance is connected in series with this coil it is observed that the current in the circuit oscillates with a frequency of 25.4 Hz. Determine the value of the added capacitance. Response in mF.