a.a. Which of the following statements about grounding electrode conductors is true? A. They restrict the ground connection. B. They eliminate potential differences between conductive objects and the Earth electrode. C. They facilitate operation of overcurrent protective devices. D. They perform bonding between the Earth and grounded conductors. a.b. Which of the following formulas would you use to find current? A. R = E ÷ I B. I = R × E C. I = E ÷ R D. E = I × R

a.a. Which of the following statements about grounding electrode conductors is true? A. They restrict the ground connection. B. They eliminate potential differences between conductive objects and the Earth electrode. C. They facilitate operation of overcurrent protective devices. D. They perform bonding between the Earth and grounded conductors. a.b. Which of the following formulas would you use to find current? A. R = E ÷ I B. I = R × E C. I = E ÷ R D. E = I × R

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter18: Lighting Branch Circuit, Receptacle Circuits For Workshop

Section: Chapter Questions

Problem 18R: List the proper trade size of electrical metallic tubing for the following. Assume that THHN...

See similar textbooks

Similar questions

List the proper trade size of electrical metallic tubing for the following. Assume that THHN insulated conductors are used. See Chapter 9, Table C1, NEC. a. Three 14 AWG ___________________ b. Four 14 AWG ___________________ c. Five 14 AWG ___________________ d. Six 14 AWG ___________________ e. Three 12 AWG ___________________ f. Four 12 AWG ___________________ g. Five 12 AWG ___________________ h. Six 12 AWG ___________________ i. Six 10 AWG ___________________ j. Four 8 AWG ___________________
1.a. Section 300.15(C) requires a fitting to be installed on each end of a conduit or tubing being used toprovide support or protection to protect the cable fromA. hazardous vapors.B. direct sunlight.C. abrasion.D. extreme heat or cold.1.b. Typically, a/an _______ is a better electrode than a ground rod because it provides a greater surface areafrom which the electrons can be dissipated.A. continuous grounding conductorB. clamp-on ground resistance meterC. rebarD. OCPD
a.2. Which of the following statements about grounding electrode conductors is true?A. They restrict the ground connection.B. They eliminate potential differences between conductive objects and the Earth electrode.C. They facilitate operation of overcurrent protective devices.D. They perform bonding between the Earth and grounded conductors.a.3. Main bonding jumpers are required to be made of _______ or other corrosion-resistant material.A. brassB. aluminumC. copperD. copper-clad aluminum
Which of the following is NOT a factor that influence the value of resistance? Select one: a. Temperature of the conductor b. Resistivity of the conductor c. Volume of the conductor d. Length of the conductor
18 - If diameter of conductor is reduced by pressure, which of the followings will occur? I- Resistance Increases II- Resistance Decreases III- Length Extends IV- Length Shortens A) I-IVB) I-IIC) Only ID) I-IIIE) Only II
25.a. Which of the following is not measured in lumens/ft2?A. ExitanceB. FootcandlesC. IlluminanceD. Candlepower 25.b- Which of the following conductors is coated with a material not recognized by the NEC as an insulation material?A. A covered conductorB. An insulated conductorC. A base conductor25.c. If you need to make a straight connection to splice two conductors (both size 4 AWG) together, whichof the following connection methods should you use?A. A pressure connectorB. A barrel crimp C. a but crimp
2. Imagine that you're asked to install an auxiliary grounding electrode at the base of a lighting pole in aparking lot. This auxiliary grounding electrode will be connected to theA. lighting pole's electrical service equipment grounding conductor.B. electrical service's grounding electrode conductor.C. next lighting pole's auxiliary grounding electrode.D. lighting pole's neutral conductor.
1) - Is a resistor an ohmic or a non-ohmic conductor? Explain in detail. 2) - Why would you plot a graph of I versus V and not V versus I. So in this case, I is the Y axis and V is the X axis
A conductor A has a diameter of 6mm and length 200cm. Conductor B has the same temperature and material as A but its diameter is 3mm and length is 1meter. What is the resistance of conductor B if conductor A has a resistance of 0.01 ohm? a. 0.02 ohm b. 0.08ohm c. 1.02 ohm d. 0.15 ohm Show solution
Calculate the length of the distribution line, if the resistivity of conductor is 1.7X10-6 Ω.cm, area of the conductor is 0.2 mm2, and the resistance is 1.36 Ω.
Calculate the direct current resistance for 1 km of a 3 cm diameter aluminum conductor? (Resistance of aluminum conductor ρ = 2.83x10-8 ꭥ-m)
The diameter of a given bare conductor is 0.50inch . A thermoplastic insulation with thickness of 0.1inch is wrapped around to insulate the conductor . Determine the insulation resistance of this conductor per meter . Assume specific resistance of thermoplastic insulation to be 2 * 10 ^ 14 ohm - cm .