Concept explainers
List the proper trade size of electrical metallic tubing for the following. Assume that THHN insulated conductors are used. See Chapter 9, Table C1, NEC.
- a. Three 14 AWG ___________________
- b. Four 14 AWG ___________________
- c. Five 14 AWG ___________________
- d. Six 14 AWG ___________________
- e. Three 12 AWG ___________________
- f. Four 12 AWG ___________________
- g. Five 12 AWG ___________________
- h. Six 12 AWG ___________________
- i. Six 10 AWG ___________________
- j. Four 8 AWG ___________________
(a)
Find the trade size EMT that is required for three 14 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that three 14 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(b)
Find the trade size EMT that is required for four 14 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that four 14 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(c)
Find the trade size EMT that is required for five 14 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that five 14 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(d)
Find the trade size EMT is required for six 14 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that six 14 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(e)
Find the trade size EMT is required for three 12 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that three 12 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(f)
Find the trade size EMT that is required for four 12 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that four 12 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(g)
Find the trade size EMT that is required for five 12 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that five 12 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(h)
Find the trade size EMT that is required for six 12 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that six 12 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(i)
Find the trade size EMT that is required for six 10 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that six 10 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
(j)
Find the trade size EMT that is required for four 8 AWG THHN conductors.
Answer to Problem 18R
The trade size
Explanation of Solution
Discussion:
Refer to Table C1, Annex C of the NEC shows that four 8 AWG THHN conductors require trade size
Conclusion:
Thus, the trade size
Want to see more full solutions like this?
Chapter 18 Solutions
EBK ELECTRICAL WIRING RESIDENTIAL
Additional Engineering Textbook Solutions
Programmable Logic Controllers
ANALYSIS+DESIGN OF LINEAR CIRCUITS(LL)
Principles and Applications of Electrical Engineering
Electric Circuits. (11th Edition)
Electric machinery fundamentals
Principles Of Electric Circuits
- A wire connector bearing no marking or reference to AL, CU, or ALR is suitable for use with (copper) (aluminum) conductors only. (Circle the correct answer.)arrow_forwardQUESTION 1 Where Type NM cables pass through cut or drilled slots or holes in metal members, the cable shall be protected by _____ which are installed in the opening prior to the installation of the cable and which securely cover all metal edges. a. plates b. listed grommets c. listed bushings d. a or barrow_forwardEighty 16 AWG copper conductors with type THWN-2 insulation are to be run in a conduit. The conduit used in an area that has an ambient temperature of 120 F. What is the maximum ampacity of these conductors?arrow_forward
- what is the largest size conductor allowed to be used with a wirenutarrow_forward6. Which of the following is a condition that a liquidtight flexible metal conduit must meet in order to be suitable as an equipment grounding conductor? A. The conduit is terminated in listed fittings.B. For trade sizes 3/4 through 1 1/4, the conduit conductors contained in the conduit are protected by overcurrent devices rated at 20 amperes or less.C. The combined length of the conduit and other tubing and conduit in the same ground-fault path exceeds six feet. D. For trade sides 3/8 through 1/2, the circuit conductors contained in the conduit are protected by overcurrent devices rated not more than 60 amperes. 7. You're going to connect a surge protection device to a separately derived electrical system. In this situation, the surge protection device should be connected at A. the load side of the first overcurrent protection device. B. the input to the transformer's primary winding.C. the end of the shortest branch circuit.D. the first connected IT cabinet. 8. What is another term…arrow_forwardRefer to the specifications in the back of this text following Chapter 33. a. What electrical codes must be conformed to? ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ b. What is the wiring method to be used in the workshop? ________________________________________________________________________ c. What size conductors are to be used for the lighting branch circuits? ______________________ AWG the small-appliance branch circuits? ______________________ AWG d. What section of the specifications tells us the size of the service entrance to be installed for this residence?arrow_forward
- a. The Code requires a minimum of two small-appliance circuits in a kitchen. Is it permitted to connect a receptacle in a dining room to one of the kitchen small-appliance circuits? _______________ What Code section applies to this situation? _______________ b. Are outdoor weatherproof receptacles permitted to be connected to a 20-ampere small-appliance circuit? _______________ c. Receptacles located above the countertops in the kitchen must be supplied by at least _______________ 20-ampere small-appliance circuits.arrow_forwardHow and where is the grounding electrode conductor attached to the water pipe?arrow_forwardAssuming all terminals are rated 75°C and you have Seven #10 AWG THHN/THWN conductors in a conduit and the conduit is run inside an office building, the largest size circuit breaker or fuse permitted to protect these wires is?arrow_forward
- Assuming all terminals are rated 75 degrees Celsius, and you have six (6) #10 AWG THHN/THWN conductors in a conduit and the conduit is run inside an office building, What is the largest size circuit breaker or fuse permitted to protect this wire?arrow_forwardAssume a bank of heating strips is rated at 22 KW and is connected to 240 volts. The heat strips operate for 4 hours at a time and are located in an area with an ambient temperature of 86 degrees F. The termination temperature rating of the heat disconnect lugs are unknown. Copper conductors with type THWN-2 insulation are to be used because of the environment of the installation to connect the heaters. What size conductors should be used?arrow_forwardWhat is the maximum size Grounding Electrode Conductor regardless of the size of the service?arrow_forward
- EBK ELECTRICAL WIRING RESIDENTIALElectrical EngineeringISBN:9781337516549Author:SimmonsPublisher:CENGAGE LEARNING - CONSIGNMENT