Soilk (mm/s)0.10300 тmB0.030.0049a.Compute the equivalent k incm/s.ACb.Compute the rate of flow incm³ /hr.15 cm15 cm15 cm»Given:Cross-sectional area of the soils A, B and C is 100 mm x 100 mm

Answered: a.Compute the equivalent k in cm/s.…

Engineering

Civil Engineering

a.Compute the equivalent k in cm/s. b.Compute the rate of flow in cm³ /hr. (

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.11P

See similar textbooks

Related questions

Q: 1. The actual velocity in the contracted section of a jet of liquid flowing from a 50 mm diameter…

A: Diameter of orifice = d = 50mm. Actual velocity = 8.54 m/sec Head = h = 4.57m

Q: 3.2. A water (Temperature = 20 °C) is flowing in a commercial steel pipe at a flowrate of 5 m³/s.…

A: Given date Pipe dia is equal to 50 centimetre Pipe length is equal to 500 m Absolute toughness is…

Q: An inverted conical tank has a base radius of 10m and height of 20m. Water flows out fre tank at…

A: V=150l H=8m

Q: In the figure, a pipe system in parallel is with a total flow of 400lit/s. determine the division of…

Q: In a two dimensional incompressible, steady flow, stream lines are drawn so that they are 20 mm…

A: given, at location A stream lines are 20 mm apart so, YA = 20 mm = 0.020 m velocity at A = VA = 5…

Q: A cast iron pipe of diameter 600 m and length 400 m caries water from a tank and discharges freely…

Q: A horizontal pipe of diameter 200mm is carrying Ethanol with density 785.1 kg/m3 at 25°C through a…

Q: The head of 15 ft causes water to flow from a large tank through an orifice and discharges to the…

A: Given data: Water Head=15 ft Diameter of orifice=3 in Coefficient of velocity=0.97 Coefficient of…

Q: Derive a relation for mass flow rate for variable head meters for compressible fluids.

Q: 25. If the capillary rise of water in 1 mm diameter tube is 3 cm, the height of capillary rise of…

Q: A fluid moves in a steady flow manner between two sections in a flow line. Calculate (a)the mass…

A: in given question for Inlet section: v1 = 30.48 m/s; A1 = 10 ft2 and p1 = 0.25 lb/ft3Outlet…

Q: 23. The ratio of the momentum correction factor to the energy correction factor for a laminar flow…

A: given- Laminar flowpipe flow

Q: What is the water velocity V (m/s) inside the given pipe? the liquid specific gravity S-9.8. 40 cm…

A: Given data in question Specific gravity Deflection of manometric fluid To find out Velocity of…

Q: A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate m of 40 kg/s. The…

Q: Oil (SG = 0.80) flows through a pipe AB 120 cm in diameter at 3 m/s and then passes through a pipe…

Q: Oil sg = 0.75 is flowing through a pipe %3D with 6 in diameter under a pressure 15 psi. The total…

A: A flow rate or rate of flow may relate to the amount of fluid passing through any part of the system…

Q: Problem 5-32 The water tank in Figure 5 - 9 is being filled through section 1 at 6 m/s and through…

Q: The tank shown in figure is of a depth d = 48.8 cm and width w =24.4 cm accelerated by ax =…

A: Depth of tank, d=48.8 cm Width of tank, w=24.4 cm Horizontal acceleration of tank, ax=3.43 m/sec2 No…

Q: ng rate of flow in open pipe like e.

A: To find : Whether the statement is true or false.

Q: 2. What height of a column of special liquid gage (s = 2.95) would exert the same pressure as a…

A: Given: The specific gravity of the liquid gage, s1=2.95 The specific gravity of the liquid gage,…

Q: Water is flowing through a cast iron pipe at the rate of 3500 GPM. The inside diameter of the pipe…

A: Answer is (d) 6.810 m/sec

Q: 3. Oil of Gs=0.80 is flowing in a pipe 8 inches diameter with a mean velocity of 12 ft/sec. The…

Q: The flow from A to E is 0.280 cum/sec. Using n = 0.058 Pipe 1 (Diameter and Length): 450 mm, 300 m…

A: Assuming n as 4f n = 0.058 = 4f Total head loss From A to D is = 165.861 meters

Q: A 1-mm diameter raindrop at standard temperature of 101.3 kPa and temperature of 20-degree C, using…

Q: What is the water velocity V (m/s) inside the given pipe? the liquid specific gravity s=9.5. 40 cm…

A: Given data Deflection of fluid Specific gravity To find Velocity

Q: The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter…

A: Solution Given Data Diameter= 50 mm Orfice= 8 m/s Head= 4.57 m

Q: What is the head loss in pipe due to friction over the length of 30 km, if the diameter of pipe is…

A: Given data: Length, L = 30 km = 30×103 m Diameter, d = 80 cm =0.8 m Velocity, v = 30 cm/s = 0.3 m/s…

Q: A pipe 200 mm in diameter and 60 m long having a sharp cornered entrance (K.=0.5) draws water from a…

Q: Referring to the figure below, the tank is being filled with water by two one- dimensional inlets.…

Q: pe 1 and Pipe 2 converges together flowing into Pipe 3. pe Discharge (LPS) Diameter (mm) 200 100 100…

Q: Refer to the given figure. Given: a = 42cm, b= 15cm, and c= 34cm Water a C 40 cm Gate Unknown liquid…

Q: 1. Determine the flow rate in cfs 2. Determine the pressure at point D in psi 3. Determine the…

A: Head loss: The reduction of the total head of the pipe when it is moved through the pipe in a given…

Q: Q1: Calculate the pressure at point A in a water flow. If the pressure at B is 87 kPa. Assume all…

A: As per guidelines plz post Q 2 separately

Q: 4) Water flows through a contraction section as shown. A pressure gage connected between the…

Q: 4. From the figure below, determine the flow rate. Assume 3K1 = K2 = 1.5K3 = 2K4 Let K1 = 3.5 x 102…

A: Introduction- The Darcy's law is a mathematical formula that explains the movement of a liquid…

Q: A square tank 4 ft on a side and 10 ft high is filled to the brim with water. Find the time required…

Q: Determine the pressure at point C in psi. Determine the pressure at point D in psi. Determine the…

A: ##Calculation for pressure at C and D , and Flow rate and velocity in pipe of dia 18 inch##

Q: Q1: Calculate the pressure at point A in a water flow. If the pressure at B is 87 kPa. Assume all…

Q: Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the…

A: Given data:- The given specific gravity is, SG=0.89

Q: The fluid shown in figure has an absolute visco 0.0010 lb.sec/ft² and specific gravity of 0.913. the…

A: For the parabolic assumption, the parabola passes through the points v=0 when y=0 v=45 when y=3

Q: Water floes through a circular pipe with a constant radius of 8cm. The speed and pressure at point a…

Q: Refer to the given figure. Given: a = 36cm, b = 24cm, and c = 29cm Water ← b с Į 40 cm Gate Unknown…

A: use simple method just find force by individual fluid and make net force zero on the gate

Q: 9.14 If the upstream velocity of the flow in Problem 9.13 is U = 1.5 m/s, determine the kinematic…

A: NOTE - I Already Answered this question before so here I'm answering again with some changes. NOTE-…

Q: 1. Water at 10°C is flowing at 0.075 m3/s. Calculate the weight flow rate and the mass flow rate.

Q: Example 2 What fraction of the mass flow rate m is diverted down the plate shown below? Neglect…

A: V1=30m/s m=5kg/s Theta=45° To find Force F

Q: The tank shown has one curved surface restraining a body of static fluid with 3.55 kPa air pressure…

A: To determine the magnitude of the resultant force on the curved surface. Given, Air pressure in…

Q: Find the speed of flow (in m/s) in the lower section. m/s Find the speed of flow (in m/s) in the…

A: Givenρ=789kg/m3 P1=1.90×104 Pa d1=7cm=0.07m Z2=y=0.35m P2=1.10×104 Pa d2=3.5cm=0.035m

Q: The circular water pipes shown in the sketch are flowing full. The velocity of flow (in m/s) in the…

A: Given data- At section P-VelocityVp=6 m/sDiameter Dp=4 mAt secton Q-VelocityVQ=5 m/sDiameter DQ=4…

Q: The components of the velocity field is given as u = 0.2 + 0.9x + 0.8y v = -0.5 + 0.9x - 0.9y…

Q: PROBLEM 2 The head of 15 ft causes water to flow from a large tank through an orifice and discharges…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Soil
k (mm/s)
0.10
300 тm
B
0.03
0.0049
a.Compute the equivalent k in
cm/s.
A
C
b.Compute the rate of flow in
cm³ /hr.
15 cm15 cm15 cm»
Given:
Cross-sectional area of the soils A, B and C is 100 mm x 100 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The section size of a water pipe is (100cm Χ 100cm), three types of soils A, B, and C are placed in the pipe, and a fixed amount of water is injected into the top left tap to keep the water head difference between the left and right ends of the pipe 60cm. The three soil permeability coefficients are k_A = 0.05 cm/sec , K_B = 0.1 cm/sec, k_C = 0.001 cm/sec, please calculate the following values:(1) The fixed amount of water injected into the faucet on the upper left (cm3/hr)(2) What is the total water head consumed by each of the three soils of A, B, and C (cm)(3) The overall volumetric seepage force of water flowing through the three soils (kN/m3)
H2 = 0.3’ h = 1.25’ H1 = 0.2’ d = 1.5” H = 0.5’ D = 4” Ksand = 0.000075 ft/min Ksilt = 0.0038 ft/min Determine: Determine the total flow of water q. Find the equivalent permeability for the soil.
5. The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. Estimate the coefficient of permeability at a void ratio of 0.48. Using Casagandre equation Using Kozeny-Carman equation Find the difference in the rate of flow using the results of “a” and “b” if i = 0.70 and A = 0.6 m2.
The hydraulic conductivities of the soils in the direction of flow through them are as follows: Soil A =0.01 cm/s Soil B=0.003 cm/s Soil C=0.00049 cm/s a) Find hA and hB (Ans. 287.86 mm and 247.44, respectively)
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the coefficient =0.05 m/s and porosity p =48%, find the transmissibility (T) in m/s per unit m, if the aquifer width is 1.2 m. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.
Find the rate of flow in m3/sec/m through the permeable soil layer. Given: H = 5.5 m, H1 = 2 m, h = 3.5 m, S = 40 m, a = 17°, and k = 0.085 cm/sec.
For a soil, given e= 0.75, w= 22%, Gs= 2.66, calculate the dry density of soil in slug/ft3. Note ρ of water= 1.94 slug/ft3 a. 3.8 b. 2.95 c. 3.6 d. 2.85 With fbd if necessary
For a soil, given e= 0.75, w= 22%, Gs= 2.66, calculate the moist density of soil in kg/m3. a.1854 b.1516 c.1860 d.1520 With FBD if necessary
Q#4: Design an irrigation channel to carry 35.5 cumecs of discharge with B/D ratio as 2.38 The critical velocity ratio is 1.2. Assume a suitable value of kutter’s rugosity coefficient and use kennedy’s method?
GIVEN THE FOLLOWING FOR A FULLY SATURATED SOIL: n=0.28 and Gs = 2.5 FIND THE WATER CONTENT. USE yw = 9.81 KN/(m^3). Use soil Mechanics
An oil tank is to be sited on a soft alluvial deposit of clay. Below the soft clay is athick layer of stiff clay. It was decided that a circular embankment, 10 m diameter,with wick drains inserted into the soft clay would be constructed to preconsolidateit. The height of the embankment is 6 m and the unit weight of the soil comprisingthe embankment is 18 kN/m3. The following data are available: thickness of softclay = 7 m, ks = 1 × 10−10 m/s and Ch = 0.6 m2/yr. The desired degree ofconsolidation is 90% in 12 months. Determine the spacing of a square grid of thewick drains. Assume wick drain of size 100 mm × 3 mm and qw = 0.1 × 10−6 m3/s.The flow point distance is 4 m. Assume a half-closed system.
Given: velocity of flow = 0.0375 m/s coefficient =0.05 m/s porosity p =48% slope S = 3/4 The soil porosity in the area where the 46-cm diameter well is 48%, find the discharge of the groundwater. Given the discharge Q get in Question #1, transmissibility T in Question#2, slope S = 3/4; find the aquifer width X.