i need the answer quickly Life of a ball bearing at a load of 8 kN is16060 h. Its life in hour, If the load is increased to 16 kN is(all other conditions are same)(A) 1000 h(B) 2000 h(C) 8000 h(D) 32000 h

Answered: Image /qna-images/answer/b635c655-0833-49e6-956e-56e24a5fb809.jpg

Answered: ad is increased to 16 kN

Engineering

Mechanical Engineering

ad is increased to 16 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes
Question 2 A load of 1.8 kN is hoisted by means of a rope on a lifting machine with a rotational frequency of 40 revolutions per min, and a drum whose diameter is 600 mm. Calculate the following: a) The power required for the load. b) Efficiency of the lifting machine, if an electric motor of 8kW is required to drive the lifting machine.
A ball bearing operating at a load F has 8000 hours of life. What is the life of the bearing, in hours, when the load is d doubled to 2F?
What is the nominal life in working hours of a deep groove ball bearing 6308, which is carrying a constant radial load of 2.82 kN at a speed of 80 rpm.
A 150 mm shaft running in a journal bearing supports a load of 10 kN and has a speed of 1200 rpm. If the coefficient of friction of the journal bearings is 0.015, which of the following is the heat generated due to friction?Group of answer choices 2.70 kW 7.06 kW 1.41 kW 2.45 kW
An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 r.p.m. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt is on the point of slipping when 3 kW is transmitted. To increase the power transmitted two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (ii) increasing the coefficient of friction by 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case.
A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 3. The center-to-center distance is 8 ft. The angular speed of the small pulley is 1850 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, F1a, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
Pulleys A and B are separated by 450 mm. The shaft has a diameter of 40 mm and is made of steel with G=75GPa�=75GPa. Pulley A has a radius of 100 mm and pulley b has a radius of 150 mm. The belt on pulley A has a tension of 4 kN in the counter-clockwise direction and a tension of 10 kN in the clockwise direction. The belt on pulley B has a tension of 6 kN in the counter-clockwise direction and a tension of 2 kN in the clockwise direction. What is the angle of twist (in degrees) of pulley B relative to pulley A?
Select a doubler row deep groove ball bearing for a radial load of 5000 N and an axial load of 6000 N, operating at a speed of 1600 r.p.m. for an average life of 8 years at 20 hours per week. Assume W /C0 = 0.50
Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
Rod AB leans against the wall with a coefficient of static friction, μSB = 0.2. The contact surface at A is smooth (μSA = 0). Find the minimum force P necessary to prevent rod AB from sliding, given:WRod = 40 lbs, L1 = 7 ft, θ = 42 °.
A belt drive is required to transmit 10 kW from a motor running at "600 rpm. The belt is 12 mm thick -and -has a mass density of 0.001 g/mm3. Safe stress in the belt is not to exceed 2.5 N/mm2. Diameter of the driving pulley is 250 mm, whereas the speed of the driven pulley is 220 rpm. The two shafts are 1.25 m apart. The coefficient of friction is 0.25. Determine the width of the belt.