2a (a)Design a forward converter to produce an output voltage of 30V whenthe input dc voltage is unregulated and varies from 150V to 175V. Theoutput power varies from 20W to 50W. The duty ratio of the switch isvaried to compensate for the fluctuations in the input dc source toregulate the output voltage at 30V.Specify:the switching frequency and range of required duty ratio of theswitch,the turns ratios of the transformer,the value of L, andiv.ii.iii.the capacitance required to limit the output ripple to less than0.2%.Your design MUST work for all operating conditions.

Answered: Image /qna-images/answer/acb1a9fc-2c51-4cd2-9660-9d6209e6c0af.jpg

(a)Design a forward converter to produce an output voltage of 30V when the input dc voltage is unregulated and varies from 150V to 175V. The output power varies from 20W to 50W. The duty ratio of the switch is varied to compensate for the fluctuations in the input dc source to regulate the output voltage at 3OV. Specify: the switching frequency and range of required duty ratio of the switch, ii. the turns ratios of the transformer, iii. the value of L, and

(a)Design a forward converter to produce an output voltage of 30V when the input dc voltage is unregulated and varies from 150V to 175V. The output power varies from 20W to 50W. The duty ratio of the switch is varied to compensate for the fluctuations in the input dc source to regulate the output voltage at 3OV. Specify: the switching frequency and range of required duty ratio of the switch, ii. the turns ratios of the transformer, iii. the value of L, and

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 2: Principles of analysis of converters in steady state.A steady state DC-DC Cuk converter is provided to you. The converter has a 24 V input, a desired 12 V output, and is operating at a switching frequency of 200 kHz. Design the circuit and calculate the required values for the inductors and capacitors. Analyze the behavior of the converter during the on and off periods.
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
Please solve this 2 problems in detail Problem 1: Consider a step up converter with a resistive load of value R=10 Ohms. It is supplied by a DC power source of magnitude Vs=220 V. The switching frequency is 4 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=20 mH. The switch is supposed to be ideal. Using the boundary conditions, the minimum and maximum load current values are equal to: Select one : a. 41.65A and 44.695A b. 43.32A and 44.695A c. None of these d. 43.32A and 47.85A Problem 2: A step up DC converter is used to control power flow from a DC votage Vs = 100V to a battery voltage E = 200V. The power transferred to the battery is 20 kw. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: a. None of these b. 0.5, 0.5 Ohms c. 0.33, 0.5 Ohms d. 0.5, 0.33 Ohms
45) We have buck converter, the maximum current of the inductor is Imax, the minimum inductor currentIs Imin. We now know the period of the switching signal is T=20 µs, the duty cycle D is 0.5, the load resistance R is 2 ohms, the input voltage is 30V, and the inductance L is 100 µH; What is Imax andIs Imin?
1.Design a buck converter and a resistive load operating in CCM mode with the following specifications:(∆V0)/V0= 0.5 %, Vin = 20 V, f =30 kHz, Duty cycle d=0.4, and R =5.33 Ω. Determine (a) the output voltage and current of the buck converter, the Critical(minimum) inductance for CCM mode (b) select L = 600 µH, find the maximum IL,max and the minimum IL,min inductorcurrents. find the capacitor value that corresponds to (∆V0)/V0= 0.5 % for this buck converter
Values of Vg = 125 V, V0 = 75 V, f = 15 kHz, R = 10  are given for the buck converter.The switch, diode, coil and capacitor used are considered ideal. According to this:a) In order that the peak-to-peak value of the coil current ripple does not exceed 5% of the rated load current valuethe inductance (L) of the coil to be used and the average output voltage of the output voltage ripple.Calculate the capacity (C) of the capacitor that should be used to be 1% of the value. b) This circuit must be used for continuous transmission (CCM) operation at 50% load.Find the minimum inductance value.
A Buck converter has the following parameters and is operating in CCM: Vin = 12V, Vout =1.8V, Lo=530nH, Co= 970 uF, ESR (Co)=5 mohm, switching frequency = 600KHz, Io = 12A Calculate : (1)The steady state duty cycle D (2)Draw the average model for the power stage (3)Draw the small signal model for the power stage (4)Calculate the small signal gain of DC in dB
Q.1. A power suppply having 220 V AC input and two fixed outputs as 10 V DC and 20 V DC is requested from you. For this purpose, a transformer with 220 V AC input / 15 V AC output, some capacitors, some silicon diodes, and zener diodes are presented.a) Design your power supply and point out DC voltage outputs b) Explain the operation of the network and all the components used in the design .c) Calculate and plot input and output signals of the network.Hint: For design, remember clipper, clamper, rectifier,voltage multiplier and zener circuits
Given the Boost Converter down below, determine: The circuits of the operation modes; The maximum current on the inductor when the following are considered: Switching frequency equal to 100kHz.Duty Cycle equal to 0,6.Input voltage equal to 10 V.Inductance is 100 µHCapacitance is 190 µFAverage current load in Ia is 1,6 A
Power Electronics. In the Buck-Boost DC-DC converter circuit:Welding voltage [40-80]VSwitching frequency (f) 25khzVoltage between load terminals 55VCapacitance value 470uFLoad current value [10-25]A Under these conditions, which is the lowest ripple (delta IL) amount of the current passing through the coil (L) in Amps for the lowest L inductance value that can keep the DC-DC converter in a continuous current state? A) 23.9803B) 118.75C) 84.3750D) 47.5E) 59.9507F) 33.75
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 20 [V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 20[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
For Steady-State Operation o f Boost DC-DC Converter What is the duty ratio (D) How can it effects on the converter output (Vo)