Adosed cylindrical tank containinga pressurized fluid has an inside diameter of 472 mm and a wall thickness of 10 mm. The tank ispressurized to 240 MPa. Determine the absolute maximum shear stress on the inner surface of the cylinder wall.40.2 MPaO 295 MPa35.0 MPaO 272 MPaO 20.9 MPa

Answered: Image /qna-images/answer/fd07c284-bc44-425e-9337-3e02f976eb78.jpg

Answered: Adosed cylindrical tank containing a…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

. Determine the surface tension in a tube with 0.2m radius and wetting angle 80 and capillary rise of 5mm in N/m and in lb/ft.
1. A cylindrical steel container 8m high and 3m in diameter is reinforced with two hoops a meter from each end. If the contained liquid is gasoline (0.87), determine the: a) total hydrostatic force and normal force acting on the wall of the tank b) tension of hoop at the bottom and at the top (c) with an allowable stress of 0.12 GPa, compute the thickness of the steel required.
3) The kinematic viscosity of the oil filled between two concentric vertical 150 mm long cylinders is 1.5 stokes. The outer diameter of the inner cylinder is 0.2 m, and the gap between the two cylinders is 1.2 mm. The inner cylinder is rotated at 200 rpm. Determine the shear stress acting in between the cylinders if specific gravity of the oil is 0.85 and also find the force required to rotates the inner cylinder.
Problem # 4: The tank shown is fabricated from steel plate. Determine the minimum thickness of plate which may be used if the stress is limited to 42 MPa and the internal pressure is 1.5 MPa. USING BOTH TANGENTIAL AND LONGITUDINAL STRESS FORMULA.
A horizontal pipe 1.0 m in diameter and 2.50 km long takes off from a reservoir 100 meters below the reservoir water surface and extends to a valve that is to be closed in 25 seconds. During closure, the flow velocity is reduced from 8 m/s to 0 m/s. Express the required thickness of the pipe in term of X. X is the distance of any section/point along the pipe from the reservoir. Use 1.24 X 105 KPa as the working stress of steel. Assume Up = 950 m/s.
A cylindrical tank has an internal pressure of 1.5Mpa. - Determine the diameter of the cylindrical tank if the strenght per meter of longitudinal joint is 480KN - Determine the diameter of cylindrical tank due to strenght of girth joint of 200KN -Determine the minimum thickness of the cylindrical tank if the stress is limited to 40Mpa
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
An inverted right circular conical tank loses water out of a 4-in hole at the bottom. The radius of the top of the tank is 8 ft and its total height is 20 ft. Assume that the coefficient of contraction is 0.6. Solve for dh/dt. Solve for dV/dt.
A hoop shrunk onto a hallow tube exert a contact pressure of 3 ksi on the tube. An internal pressure of 10 ksi is then applied to the tube. The inner and outer radii of the tube are 1.5 in and 2.5 in, and 2.5 in and 4 in for the hoop. What is the maximum tangential strss in the tube after application of internal pressure? Also plot tangential stress variation diagram across the section.
Determine the limiting peripheral velocity of a rotating steelring if the allowable stress is 150 MPa and the mass density ofthe material is 7800 kg/m3.
The constructed shaft is composed of a tube AB and a solid bar BC. The tube has an inner diameter of 20 mm and an outer diameter of 28 mm. The bar has a diameter of 12 mm. Determine the average normal stress at points D and E and identify whether the points are in compression or tension.answer:σD = -13.26 Mpa (compression) σE = 70.74 Mpa (traction)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Adosed cylindrical tank containing a pressurized fluid has an inside diameter of 472 mm anda wall thickness of 10 mm. The tank is pressurized to 240 MPa. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. O 40.2 MPa O 295 MPa O 35.0 MPa O 272 MPa 20.9 MPa