After creating her standard curve for absorption versus the concentration (M) of FD&C Red 40 and processing her data, Sally found that her drinking strength Kool-Aid sample had an FD&C Red 40 concentration of 1.086 x 10–5 M. If 0.133 grams of Kool-Aid powder was used to prepare an 8-fl oz cup of her assigned flavor, what is the percent by mass of FD&C Red 40 in her Kool-aid powder?

After creating her standard curve for absorption versus the concentration (M) of FD&C Red 40 and processing her data, Sally found that her drinking strength Kool-Aid sample had an FD&C Red 40 concentration of 1.086 x 10–5 M. If 0.133 grams of Kool-Aid powder was used to prepare an 8-fl oz cup of her assigned flavor, what is the percent by mass of FD&C Red 40 in her Kool-aid powder?

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter11: Atomic Mass Spectrometry

Section: Chapter Questions

Problem 11.10QAP

See similar textbooks

Similar questions

After creating her standard curve for absorption versus the concentration (M) of FD&C Red 40, a student found that her best fit linear line for FD&C Red 40 was y = 2,962x + 0.005. Her Kool-Aid sample had an absorbance of 0.685. If 0.543 grams of Kool-Aid powder was used to prepare an 8-fl oz cup of her assigned flavor, what is the percent by mass of FD&C Red 40 in her 8-fl oz cup?
RMR (kcal/day) = (9.99 x 79.5kg) + (6.25 X 182.9cm) - (4.92 x 35) + (166 x 1)- 161
Explain the use of plans and their importance in assessing the quality of pharmaceutical products. Provide a step-by-step design of a sampling plan based on a normal inspection for a 75,000 tablets with an AQL of 0.12% using the attached table (at the end of exam paper).
A 0.1 g amine-containing compound is dissolved in water then diluted to 100 mL. You subject it to spectroscopic analysis, in order to get the concentration of amine in this compound. Next, you get 1 mL of the previously diluted sample then dilute it again to 250 mL for measurement. Then, you fill 3/4 of a 1-cm cuvette with this diluted sample, and you run an analysis using an AAS. The recorded absorbance is 0.545 at 410 nm. What is the molecular weight of the compound? (The molar absorptivity is 1.23 x 104 cm-1 mol-1 L.)
A series of standards were analyzed which gave the following results SOLUTION % Transmittance 0 mL of 0.100 mg/mL Hg + 2 mL tinchloride in a total volume of 75 mL 100 1.0 mL of 0.100 mg/mL Hg + 2 mL of tinchloride in a total volume of 75 mL 81.3 2.0 mL of 0.100 mg/mL Hg + 2 mL of tinchloride in a total volume of 75 mL 63.9 3.0 mL of 0.100 mg/mL Hg + 2 mL of tinchloride in a total volume of 75 mL 55 5.0 mL of 0.100 mg/mL Hg + 2 mL of tinchloride in a total volume of 75 mL 35.1 How would you make a Beer-Lambert Plot with this information?
What are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?
A volumetric calcium analysis on triplicate samples of the blood serum of a patient believed to be suffering from a hyperparathyroid condition produced the following data: mmol Ca/L = 3.15, 3.25, 3.26. What is the 95% confidence interval for the mean of the data, assuming no prior information about the precision of the analysis?
Chemistry The most abundant type of mammalian antibody circulating in the blood stream is IgG. A solution prepared from 0.798 g of a particular IgG in 250 mL of water shows an absorbance of 0.578 at 275 nm in a 1.00 cm cell. If the molar absorptivity of the IgG is 6.49 × 104 M–1 cm–1 at 275 nm, what is the molar mass of the IgG? Present your numerical answer in kg·mol-1 to 3 significant figures .
4.A student carried out a simple distillation on a compound known to boil at 124°C and measured a boiling point of 116-117°C. Gas chromatography(a technique for assessing purity)showed that the compound was pure and a calibration check on the thermometer was positive. What might be wrong with the distillation apparatus setup?
2. A study of body mass index (BMI) in adults showed that for men aged 40–44, the mean BMI level is 26.7 with a standard deviation of 3.7. Assuming a normal distribution, what percentage of men in this age group have a BMI between 30.0 and 35.0?
You are trying to come up with a drug to inhibit the activity of an enzyme thought to have a role in liver disease. In the laboratory the enzyme was shown to have a Km of 1.0 x 10-6 M and Vmax of 0.1 micromoles/min.mg measured at room temperature. You developed a competitive inhibitor. In the presence of 5.0 x 10-5 M inhibitor, the apparent Km of the enzyme was found to be 1.5 x 10-5 M. What is the Ki of the inhibitor?
Julie has been asked to measure the concentration of a sample solution using a spectrophotometer. After a first attempt, she realizes that, to make the measurement, she must first dilute the sample solution. Julie transfers 2.3 mL2.3 mL of the sample to a 250 mL250 mL volumetric flask and fills the rest of the flask with water to the 250 mL250 mL line. She then uses the spectrophotometer to measure the concentration of the dilute solution as 5.5×10−5 M.5.5×10−5 M. What is the concentration of the starting sample solution? sample solution concentration: M