i need the answer quickly wo centrifugal pumps are connected in parallel in a given pumping system. Plot total headnst capacity Q pump and system curves for both pumps running on the basis of thefollowing data:operating data for pump 1Ah, mOs, m³ /h40353025169209239265operating data for pump 2Ah, mQs, m³/h40353025136203267Data for systemAh, mOs, m³/h20253035244372470

Answered: Image /qna-images/answer/2861418e-c84d-4756-b258-d863d7c35c22.jpg

Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two centrifugal pumps are connested in parallel in a given pumping system. Plot total hed following data: operating data for pump 1 Ah, m Qs, m³/h 40 35 30 25 169 209 239 265 operating data for pump 2 Ah, m Qs, m3/h 40 35 30 25 136 203 267 Data for system Ah, m Qs, m3/h 20 25 30 35 244 372 470

Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two centrifugal pumps are connested in parallel in a given pumping system. Plot total hed following data: operating data for pump 1 Ah, m Qs, m³/h 40 35 30 25 169 209 239 265 operating data for pump 2 Ah, m Qs, m3/h 40 35 30 25 136 203 267 Data for system Ah, m Qs, m3/h 20 25 30 35 244 372 470

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q-- Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Explain why some pump performance curves may lead tounstable operating conditions.
A multi stage pump is required to deliver of 2 l/s water against a maximum discharge head of 240 m. The diameter of radial bladed impeller should not be more than 15 cm. Assume a speed of 2800 rpm. Determine the impeller diameter, and power. Overall efficiency is 0.7.
Fluid Mechanics. plz, solve all the parts from a , b and c Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
You are asked to calculate a rotadynamic pump with a total manometric head of 11 mss and demand flow of 19 in lt / s, which will meet the daily water need of a facility, and which can rotate at 1450 rpm for its drive, using a three-phase electric motor. Since the density of the water to be transported is 1000 kg / m3; a) Calculate the pump organs.
Briefly discuss what makes Centrifugal Pump not to be classified as a Positive Displacement Type of Pump? Also, explain the reason why cavitation will occur in centrifugal pumps and not in Displacement pump?
The MITL ME laboratory has installed a double-suction, three-stage, centrifugalpump with a discharge of 330 gpm under 200 ft head and running at 1200 rpm. It isproposed to install another pump with double suction and six stages, but of the samecharacteristics, to operate at 98 ft head and deliver 430 gpm. Calculate a) the speed ofthe proposed pump; b) the impeller diameter of the proposed pump if the diameter of theexisting pump is 6 inches; and c) the type of the existing and the proposed pump.
A two-lobe rotary positive-displacement pump, similar to that of Fig, moves 3.64 cm3 of tomato paste in each lobe volume Vlobe. Calculate the volume flow rate of tomato paste for the case where n. = 336 rpm
It is desired to pump 50 ft3/s of water at a speed of 22 r/s,against a head of 80 ft. (a) What type of pump would yourecommend? Estimate (b) the required impeller diameterand (c) the brake horsepower.
Flow turbulence and cavitation in a centrifugal pump generate a similar sound to the human ear. Explain how vibration analysis would help you to determine which is which.
A centrifugal pump delivers 25 liters of water per second against a head of 10 meters and running at 1300 rpm requires 10 kW of power. Determine the discharge, head of the pump and power required if the pump runs at 1500 rpm. (Ans. 0.0288cumec or 1.73 cu.m./min , 13.31m, 15.36kw)
Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.