W hen the galvanized ion sheets com e w ith dim ensions (2x1)m.Calulate the rum ber of sheets equined to m ade the ectangular duct system shown in figure below w hen it sized using equal friction m ethod w ith frictionalpressue dop of 1pam and alow able height is 300 mm. 0.6 m /s 0.6 m /s 3 2m 2m 2m F 2m Fan E 2m B A 5m

W hen the galvanized ion sheets com e w ith dim ensions (2x1)m.Calulate the rum ber of sheets equined to m ade the ectangular duct system shown in figure below w hen it sized using equal friction m ethod w ith frictionalpressue dop of 1pam and alow able height is 300 mm. 0.6 m /s 0.6 m /s 3 2m 2m 2m F 2m Fan E 2m B A 5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Impeller in a centrifugal pump as shown in the figure is connected to the shaft with CONICAL CLEANER. The power to be transmitted by the motor is P = 23 kW. Its revolution is n = 1822 rpm. Width of the conical joint is b=96mm, Conical angle α = 1 degree, Friction coefficient μ =0.3. The conical connection is tightened up to the limit of the surface safety pressure (Pem=39 N/mm2, the shear safety stress of the shaft τem=22 N/mm2) After finding the required SHAFT DIAMETER, HOW MUCH IS the connection safe or not in order to transmit this force. (Attention! and the ratio of the torque coming from the motor gives safety)
The load carrying crane shown in the figurethe drum with its rope wound with one hydromotorare driven. Object A is slanted as the rope hugsIt moves up and down over the sled.The diameter of the drum on which the rope is wound is 300 mm.All hydraulic system until hydromotor30% of pressure losses in the components (efficiency 0.7)It will be taken. Thread of hydraulic gear pump in one round0.8 lt of oil dispensed from the cavitiesSince it isa. Calculate the flow of the pump (lt / min)b. Find the working pressure of the pump (bar)Load speed v = 0.6 m / sTensile force on the rope T = 10,000 NIt will be taken.
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where the shutoff head H0 = 125 ft of water column, coefficient a = 2.50 ft/(gpm)2 , available pump head Havailable is in units of feet of water column, and capacity V. is in units of gallons per minute (gpm). Estimate the capacity delivered by the pump
Find the minimum diameter of a smooth tube to ensure the flow of water at an average velocity of 100 cm/s remains turbulent. Use vwater = 1E-6 m2 /s. [Ans.: 4 mm]
6. P, Thrust washer A sluice gate weighing 18 kN is raised and lowered by means of square threaded screws, as shown in Fig. 10.30. The frictional resistance induced by water pressure against the gate when it is in its lowest Nut position is 4000 N. The outside diameter of the screw is 60 mm and pitch Screw is 10 mm. The outside and inside diameter of washer is 150 mm and 50 mm respectively. The coefficient of friction between the screw and nut is 0.1 and for Fig. 10.30 the washer and seat is 0.12. Find : 1. The maximum force to be exerted at the ends of the lever for raising and lowering the gate, and 2. Efficiency of the arrangement. [Ans. 114 N; 50 N ; 15.4%
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where shutoff head H0 = 24.4 m of water column, coefficient a = 0.0678 m/(Lpm)2 , available pump head Havailable is in units of meters of water column, and capacity V. is in units of liters per minute (Lpm). Estimate the capacity delivered by the pump. A
A pump, for which the characteristic curve is shown below, is used to pump water from a canal into a dam. The pump is mounted 2.0 m above the water level. There is a 50 mm PVC pipe connected to the suction side of the pump, and a 40 mm PVC pipe connected to the discharge side. The total length of pipe on the suction side is 8 m, and there is a strainer (K = 20), a non-return valve, a 90° elbow and a fully open gate ball valve in the suction line. Another fully open gate valve, and two 90° elbows are mounted in the discharge line. The total length of the discharge line is 60 m, and the discharge pipe outlet is 4 m above the pump. You may assume a water temperature of 25 °C. Determine: (a) The flow rate through the system(b) The required fluid power(c) The efficiency of the pump(d) Whether the pump will cavitate or not.
sollve both, show both solutions and steps for both problems
1. A pelton type turbine was installed 30 m below the head gate of the penstock. The head loss due to friction is15% of the given elevation. The length of the penstock is 80 m and the coefficient of friction is 0.00093.Determinea) the diameter of the penstock in mm. (421.6 mm)b) the power output in KW (781.234 KW)
Determine the smallest metric hydraulic copper tube size that will carry 4L/min of thefollowing fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline(SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C. answer correctly the last part only please thank you
Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline (SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C.
ity of 25 m/s. 1 he pressures; Iy while the datum head at WJ A pipe of diameter 400 mm carries water L oints A and B are given as 29.43 Nfem” and 22.563 Nfcm respective B are 28 m and 30 m. Find the loss of head betweert A and B