ähäi 30 For a damped one DOF system where m, c, and k are shown below: (a) k = 10 N/m, m 10 %3D kg, c = 10 kg/s, (b) k = 2.5 N/m, m = 10 kg, c = 10 kg/s, (c) k = 1 N/m, m = 10 kg, c = 10 kg/s. %3D %3D Calculate for each case the value of natural frequency in rad/sec; time of period in sec; critical damping coefficient, damping ratio; Are these systems overdamped, underdamped, or critically * ?damped

ähäi 30 For a damped one DOF system where m, c, and k are shown below: (a) k = 10 N/m, m 10 %3D kg, c = 10 kg/s, (b) k = 2.5 N/m, m = 10 kg, c = 10 kg/s, (c) k = 1 N/m, m = 10 kg, c = 10 kg/s. %3D %3D Calculate for each case the value of natural frequency in rad/sec; time of period in sec; critical damping coefficient, damping ratio; Are these systems overdamped, underdamped, or critically * ?damped

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Determine the driven response for: Bi k B2 k mi m2 Given: ID k spring constant, mě – mass, B: - damping coefficient, F(t) Initial data: ID = 500351 ID % 4 = 1
Vibrations Question It is observed from the magnitude plot of a compliance transfer function of a mass spring damper that the value at a very small frequency 0.0001 is 3.71 meters and at resonance 1.10 rad/s is 7.10 meters. What is the natural frequency, damping coefficient, stiffness, and mass of the system?
Based on the pic attached, If component B of #6 is changed to 3 parallel components and each has thesame reliability, what is the system reliability now? pls provide celaar solutions detailed thanks
Compute the maximum percent overshoot 100Mp and the 2% settling time ts that correspondto wn = 1 ???/???, damping ratio= 0.707.
A spring-mass-damper system oscillating about the horizontal surface is subjected to anexternal force of F = 300 sin (6)(t), where 300 is in Newtons and 6 is in radians per second. Thesystem has a mass 90 [kg], a damping coefficient of 78 [N ⋅ s/m] and a spring constant of300 [N⁄m]. The system is both given an initial displacement of 1.2 [m] and an initial velocity of 1.4[m⁄s].a. Using Method of Undetermined Coefficients, determine the particular solution for thedisplacement function.b. Determine the unknown coefficients for the homogeneous solution using the initialconditions (Note: the external force already works at t = 0).c. Determine the position, velocity, and acceleration of the system after 10 seconds.
Figure 1 shows a system comprising a bar with mass m-12 kg and the length of the bar L=2 m, two springs with stiffness kt=1000 N-m/rad and k = 2000 N/m, one damper with damping coefficient c=50 N-s/m and two additive masses at the end of the bar, where each mass (M) is equal to 50 kg. The rotation about the hinge A, measured with respect to the static equilibrium position of the system is 0 (t). The system is excited by force (F) so find the state space representation of the system if the output y=ġ(t).
It is observed from the magnitude plot of a compliance transfer function of a mass spring damper that the value at a very small frequency 0.0001 is 3.71 meters and at resonance 1.10 rad/s is 7.10 meters. What is the natural frequency, damping coefficient, stiffness, and mass of the system?
(b) Consider a vertical spring mass-damper-system with mass m = 2 kg, damping coefficient c = 5 N.s/m and stiffness k = 10 N/m. An external force f(t) = sin3t N is applied to the mass. (i) Find the static equilibrium position as measured from the un-stretched length of the spring (ii) Write the equation of motion. (iii) Find the natural and damped frequencies. (iv) In steady state, find the time delay in seconds between the mass position and f(t). (v) Find the steady state maximum acceleration.
What is the deformation response factor for a damped system with stiffness of 800N/m, and a mass of 18kg? The system is being forced by an oscillating load of 6sin(2πt)kN and has a damping ratio of 0.33. Give the solution to 3dp.
Write the phase condition of resonance in damped system. (hint: The unit of the answer is the degree. )
Q3.Consider a spring–mass–damper system with m = 80 kg, c = 15 kg/s, and k = 1500 N/m with an impulse force applied to it of 1200 N for 0.01 s. (C) Calculate the damped natural frequency of the system (D) Calculate the system response to the impulsive force at time t = 1 s
A machine is represented as a single degree of freedom spring-mass-damper system. The machine has a total mass of (109)kg, an out-of-balance mass 0.125 kg, eccentricity of 0.01 m, coefficient of damping (109)N/ (m/sec), and spring stiffness (1009) N/m. The rotational speed of the machine is 3000 rpm. Determine the maximum amplitude of vibration due to out-of-balance. Suggest a method for the control of vibration caused due to out-of-balance.