Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 3 cm thick. The convection heat transfer coefficient on the upper surface is 30 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = ..... kJ.

Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 3 cm thick. The convection heat transfer coefficient on the upper surface is 30 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = ..... kJ.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.49P

See similar textbooks

Similar questions

(04) A thin fat plate ( 45 cm X 90 cm ) is immersed in a stream of glycerin Tp= 1258 kg/m° and u = 1.49 Pa.s) with a velocity of (7 m/s ). Compute the skin frictional (viscous ) drag exerted on the upper surface of the plate, if : a) The plate side parallel to the stream is the shortest side b) The plate side parallel to the stream is the longest side You may use the following relations: CDIam = 1.328 / ReL 1/2 Cpturb = 0.072 / ReL 1/5
1-The wind blows with velocity 0.4 m/s parallel to the both sides of a flat plate with rectangular area 10m×10 m. The plate temperature is T0=60◦C, and the temperature of the air free stream is 20◦C. Assume laminar flow and calculate: (a) maximum boundary layer thickness, (b) the total force experienced by the plate, (c) estimate the total heat transfer rate by laminar forced convection (d) Make a qualitative sketch of how the local heat flux qx and τx varies along the length L.
Atmospheric air with free flow velocity U_∞= 30 m/s flows through a circular cylinder at T_∞= 250 K and D = 2.5 cm diameter. The surface of the circular cylinder is kept at a uniform temperature T_w = 350 K.The CD drag coefficient is 1.1. (D=1 cm- 3 cm and U_∞= 10 m/sec 30 m/s)(a) Calculate the average heat transfer coefficient ( h ̅_m,W/m2K)(b) Determine the amount of heat transfer (Q, W) per 1 m length of the cylinder(c) Calculate the drag force (FD, N) acting on the 1 m length of the cylinder FD=0.1 A=0.34 D=2.9 cd=1.2
Air at 30°C flows over a 3.0-cm-outer-diameter, 45-m-long pipe with a velocity of 6 m/s. Calculate the drag force exerted on the pipe by the air. (Air properties at 30°C are: ? = 1.164 kg/m3, ? = 1.608 × 10−5 m2/s.) (a) 19.3 N (b) 36.8 N (c) 49.3 N (d ) 53.9 N (e) 60.1 N
A thin flat plate ( 45 cm X 90 cm ) is immersed in a stream of glycerin ( ρ = 1258 kg/m3 and μ = 1.49 Pa.s ) with a velocity of ( 7 m/s ). Compute the skin frictional ( viscous ) drag exerted on the upper surface of the plate, if : a) The plate side parallel to the stream is the shortest side b) The plate side parallel to the stream is the longest side You may use the following relations: CDlam = 1.328 / ReL^(1/2) CDturb = 0.072 / ReL^(1/5)
Air at 22˚C and at atmospheric pressure flows over a flat plate at a velocity of 1.65 m/s. If the length of the plate is 2.179 m and its temperature is 98 ˚C, Calculate Heat rate by using exact and approximate methods both. What is the %age difference of the heat transfer rate values by these methods? Take width of the plate as unity. Properties given at 60˚C are as follows: Density: 1.058 kg/m3 , cp = 1.005 kJ/kg˚C, k= 0.02897 w/m˚C, Kinematic viscosity is 18.97 × 10-6 m2 /s
The following equation may be used to estimate the take-off ground run for an aircraft: Equation has been attached as an image. Calculate the take-off ground run, from a runway at ISA-SL conditions, for a twin engine aircraft for which the following data may be assumed Aircraft lift-off speed 155 knots Max take-off gross weight 220 tonnes Wing planform area (S) 358 m Wing CL (t/o flaps deployed, a = 0) 1.1 Wing span 53.18 m Oswald efficiency factor, e 0.7 KGE = CD(IGE) / Co(OGE) 0.4 Co sum (fuselage, wing, tailplane and nacelle) 0.015 Co for undercarriage 0.021 Co for flaps at taking-off setting 0.0073 Coefficient of rolling friction, u 0.02 Engine thrust (assumed constant) 310 kN per engine It may be assumed that 1knot = 0.51444 m/s It may be assumed that 1knot = 0.51444 m/s
Heat transfers Water (T= 10 C, , k=0.644 W/m.C, υ = 5.54× 10^-7 m2/s, Pr=3.55), flow over plate 1m x 1m , with velocity 2 m/s. the plate surface temperature is 90 C. Give the answer for the following: Nu number equal to Total heat transfer The flow type The average heat transfer coefficient
3.) Automotive engineers work very hard to improve the value of the drag coefficient for cars. Suppose you have a car with a mass of 3000. kg and an effective surface area of 4.00 m^2. The engine can generate a maximum force of 28,000. N. Let the coefficient of kinetic friction be 0.200, and the coefficient of static friction be 0.400. Air has a density of 1.21 kg/m^3. (back on earth) (3a) Draw a free-body diagram for your car, including both drag and friction, when the car is moving at its maximum velocity. (3b) If the maximum value of your car's velocity is 150.0 m/s, then what is the drag coefficient for the car? (3c) Suppose your engineers change the drag coefficient to 0.300 - what would be your maximum velocity then with the same force from your engine.
A steam generator generates flue gas at an average temperature of 260 C inside a Chimney. The theoretical draft is 0.5 kPa and the ambient condition of the air is 21 C and 100 kPa. Assume the coefficient velocity to be 0.30 and the molecular weight of the flue gas is 32. For air-fuel ratio requirements per second of 15, calculate: a. The diameter of the Chimney, meter b. The theoretical draft, cm H₂O
1) Calculate the drag force (unit: N) of a sphere particle in 20°C water. Know the diameter of the particle = 1 cm; the Reynolds number of water = 1; dynamic viscosity of 20°C water = 0.001 kg/ms; velocity of the particle = 0.02 m/s. 2) When calculate the lift coefficient, the area A in the equation is: a) surface area b) planform area c) cross-sectional area d) frontal area 3) The sum of the components of the pressure and wall shear forces (a) in the flow direction is called ____ and (b) in the normal direction is called ____. a) Friction, Pressure b) Lift, Drag c) Pressure, Friction d) Drag, Lift
Assume Patm = 10^5, Pa = 14.7 psi ; ρwater ~ 1000 kg/m3 ; ρair ~ 1.2 kg/m3 ; μwater ~ 10^-3 N•s/m2 ; μair ~ 2 x 10^-5 N•s/m2 ; Vwater ~ 10^-6 m2 /s ; Vair ~ 1.67 x 10^-5 m2 /s ; g = 9.8 m/s^2 .; 1 m/s = 2.24 mph ; 1lbf = 4.45 N ; 1 m^3 = 264 gallons The drag data for a Brazuca soccer ball ( take M = 0.5 kg, D = 0.2 m)