Air flows steadily adiabatically through a pipe with a constant cross-sectional area. Air is fed into the pipe through an isentropic converging nozzle from a large tank where the pressure and temperature are 900 kPa and 300 K, respectively, as shown in the figure below. The pressure at the inlet of the duct is 750 kPa. If the temperature at the duct exit is 275 K, determine the pressure at the duct exit. Ans. pe = 568.7 KPa

Air flows steadily adiabatically through a pipe with a constant cross-sectional area. Air is fed into the pipe through an isentropic converging nozzle from a large tank where the pressure and temperature are 900 kPa and 300 K, respectively, as shown in the figure below. The pressure at the inlet of the duct is 750 kPa. If the temperature at the duct exit is 275 K, determine the pressure at the duct exit. Ans. pe = 568.7 KPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass ﬂow rate 6 kg/s. The outlet pressure is 100 kPa and assume that speciﬁc heats are constant and evaluated at 600 K. 1. How much power is produced in kW? Round your answer to the nearest whole number. 2. What is the outlet temperature in K? Round your answer to one decimal place.
A nozzle operates with steam entering at 700 kPa and 300 °C. The velocity at the inlet is 30 m/s. As the steam flows through the nozzle, the pressure decreases. Determine the area ratio value (Area / Area inlet), where Area inlet is the cross sectional area of the nozzle at the inlet, at the sections of the nozzle where the pressure values are 650, 550, 450, 350, and 250 kPa. Assume nozzle operates isentropically.
What happens to steam pressure and velocity in a diverging nozzle?
Hydrogen enters a steady-ﬂow and adiabatic compressor at 310 K and 95 kPa and exits at a pressure of 400 kPa. The amount of work required is 2400 kJ/kg of hydrogen. Assume that speciﬁc heats are evaluated at the inlet temperature. 1.What is the outlet temperature, in K? Report your answer to one decimal place using rounding and use an appropriate amount of significant figures for intermediate calculations. 2. Calculate the amount of entropy generated in kJ/kg K. Round to three decimal places.
Dry saturated steam at a pressure of 8 bar enters a convergent divergent nozzle and leaves it at a pressure of 1.5 bar. If the flow is isentropic and if the corresponding expansion index is 1.135, Determine the ratio of crosssectional area at exit and throat for maximum discharge
For a gas turbine jet propulsion unit, the pressure and temperature entering the compressor are 1 atm and 15 oC respectively. The pressure ratio across the compressor is 6 to 1 and the temperature at the turbine inlet is 1000oC. On leaving the turbine the air enters the nozzle and expands to 1 atm. Determine the pressure at the nozzle inlet and the velocity of the air leaving the nozzle.
Air at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass ﬂow rate 6 kg/s. The outlet pressure is 100 kPa and assume that speciﬁc heats are constant and evaluated at 600 K. 1. How much power is produced in kW? Round your answer to the nearest whole number. 2. What is the outlet temperature in K? Round your answer to one decimal place. 3. Select all appropriate assumptions Non-ideal gas. Ideal gas Steady flow Unsteady flow Adiabatic Neglect kinetic and potential energy Account for kinetic and potential energy No work Isobaric Isothermal Isochoric Isentropic Exact analysis Approximate analysis
Please Help,will provide helpful e Ratings for correct solution. Thank You. Water flows through a horizontal coil through which high-temperature flue gas passes. As water passes through the coil, it passes from the liquid phase at 200 kPa and 80°C to the vapor phase at 100 kPa and 125°C. The entry speed of water into the coil is 3 m/s and the exit speed of steam is 200 m/s. Calculate the heat transferred per unit mass of water through the coil? The enthalpies of the inlet and outlet streams are given as 334.9 kJ/kg and 2726.5 kJ/kg, respectively.
An aircraft is flying at a cruising speed of 250 m/s at an altitude of 5000 m where the atmospheric pressure is 54.05 kPa and the ambient air temperature is 255.7 K. The ambient air is first decelerated in a diffuser before it enters the compressor. Approximating both the diffuser and the compressor to be isentropic, determine (a) the stagnation pressure at the compressor inlet and (b) the required compressor work per unit mass if the stagnation pressure ratio of the compressor is 8.
Air with mass flow rate of 1 kg/s enters the first stage of a compressor at 100 kPa and 300 K and exit the second stage of the compressor at 2677 kPa. If the compressed air outgoing from the first stage of the compressor passes through an intercooler, then enters the second stage of the compressor at temperature 353 K. What is the indicated isothermal efficiency for the compressor assuming ideal compression process with polytropica index n = 1.3 for both stages, no pressure loss in the intercooler, and the pressure ratio across the first and the second stage of the compressor are equal?
A three-stage compressor receives 500 lps of air at 101 kPaa and 27 oC, anddischarges at 750 kPaa. Determine a) the power required; b) the pressure at eachintercooler; c) the maximum temperature; and d) the heat transferred in each intercooler.e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?(answers for Letter D and E Thank you)
The enthalpy of steam entering the turbine inlet is 2750 kJ/kg and leaving turbine at 1750 kJ/kg. The enthalpy of saturated liquid is 190 kJ/ kg and enthalpy of dry saturated steam 2600 kJ/kg corresponding to the condenser pressure. The quality of steam at the exit of turbine is