If all forces on the free-body diagram of a body can be computed using onlyequilibrium analysis, the forces are said to be? *Statically determinate problemsO all of the aboveO Statically Indeterminate problemsO EquilibriumIn the xy- plane biaxial loading, the stress in z-direction is? *none of the abovesame stress in y-directionsame stress in x- directionzero

all forces on the free-body diagram of a body can be computed using only equilibrium analysis, the forces are said to be? * Statically determinate problems all of the above O Statically Indeterminate problems O Equilibrium In the xy- plane biaxial loading, the stress in z-direction is? * none of the above same stress in y-direction same stress in x- direction zero

all forces on the free-body diagram of a body can be computed using only equilibrium analysis, the forces are said to be? * Statically determinate problems all of the above O Statically Indeterminate problems O Equilibrium In the xy- plane biaxial loading, the stress in z-direction is? * none of the above same stress in y-direction same stress in x- direction zero

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter5: Further Applications Of Newton's Laws: Friction, Drag, And Elasticity

Section: Chapter Questions

Problem 31PE: (a) The "lead" in pencils is a graphite composition with a Young's modulus of about 1109 N/ m2....

See similar textbooks

Similar questions

A farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands more than the glass when it warms up, in such a way that the volume increases by 0.2% (that is, V/V0=2103 ) relative to the space available. Calculate the magnitude of the normal force exerted by the juice per square centimeter if its bulk modulus is 1.8109 N/m2, assuming the bottle does not break. In view of your answer, do you think the bottle will survive?
(a) The "lead" in pencils is a graphite composition with a Young's modulus of about 1109 N/ m2. Calculate the change in length of the lead in an automatic pencil if you tap it straight into the pencil with a force of 4.0 N. The lead is 0.50 mm in diameter and 60 mm long. (b) Is the answer reasonable? That is, does it seem to be consistent with what you have observed when using pencils?
One end of a vertical metallic wire of length 2.0m and diameter 1.0mm is attached to a ceiling, and the other end is attached to a 5.0N weight pan, as shown below. The position of the pointer before the pan is 4.000cm . Different weights are then added to the pan area, and the position of the pointer is recorded in the table shown. Plot stess versus strain for this wire, then the use the resulting curve to determine Young’s modulus and the proportionality limit of the metal. What metal is this most likely to be?
When using a pencil eraser, you exert a vertical force of 6.00N at a distance of 2.00cm from the hardwood-eraser joint. The pencil is 6.00mm in diameter and is held at an angle of 20.0 to the horizontal. (a) By how much does the wood flex perpendicular to its length? (b) How much is it compressed lengthwise?
Bruce Lee was famous for breaking concrete blocks with a single karate chop. From slow-motion video, the speed of his 1.50-kg hand descending on a block was estimated to be 15.0 m/s, which decreased to a speed of 0.500 m/s in the 2.50 103 s during which his hand made contact with and broke through the block. The maximum shear stress a concrete block can be subjected to before breaking is 9.50 105 N/m2. a. What was the force exerted by Lees hand on the block? b. If a typical concrete block broken by Lee was 3.00 cm thick and 15.2 cm wide, what is the shear stress experienced by the concrete block? c. Will the concrete block succumb to Lees karate chop?
he stress-strain graphs for materials A and B are shown below. The graphs are drawn to the same scale. Which of the two is the stronger material? A about the same B
The stress-strain graphs for materials A and B are shown below. The graphs are drawn to the same scale. Which of the materials has the greater Young's modulus? about the same A B
Dynamic climbing ropes are designed to be quite pliant, allowing a falling climber to slow down over a long distance. The graph shows forceversus- strain data for an 11-mm-diameter climbing rope. What is the Young’s modulus for this rope?
In some recent studies it has been shown that women are more susceptible to torn anterior cruciate ligaments, or ACLs, than men when competing in similar sports (most notably in soccer and basketball). Select the statement that explains why this disparity might exist. The ACL of women is more elastic than the ACL of men. The Young's modulus of women's ACLs is typically smaller than that of men's, resulting in more stress for the same amount of strain. The cross-sectional area of the ACL is typically larger in men, and therefore experiences less strain for the same tensile force and Young's modulus. The cross-sectional area of the ACL is typically smaller in women, and therefore experiences less stress for the same tensile force.
The "lead" in pencils is a graphite composition with a Young's modulus of approximately 1.0 ✕ 109 N/m2. Calculate the change in length (in mm) of the lead in an automatic pencil if you tap it straight into the pencil with a force of 4.5 N. The lead is 0.70 mm in diameter and 51 mm long. (Enter the magnitude.)
A little girl pushes on her toy bus by applying a force of 15N oriented 25 degrees below the horizontal to set it in motion. The toy bus has a mass of 2kg and rolls on the floor. 1) Calculate the modulus of the normal force felt by the bus: ?= ?? 2) Calculate the resultant force felt by the bus by giving its two components: FR=( ? i+ ? j )N
A hammer strikes a metal disk with 150N of force, temporarily making the 25.0mm3 disk lose 0.2mm3 of volume before it snaps back. If the disk has a top surface area of 120mm2 and completely fits under the hammer’s striking face, what is the relevant elastic modulus of the metal? Do not actually solve the problem numerically or algebraically, just pick the one equation and define the relevant knowns and single unknown.