All of the following statements are correct except A) The intensity of an internal force over a sectioned area is referred to as stress. B Shear stress arises whenever the applied loads cause one section of a body to slide past its adjacent section. If a prismatic bar is subjected to an axial force acting through the centroid of the cross-sectional area, the stress is averaged over the entire cross-section. D A material exhibits elastic behavior if deformation remains even after removal of force applied.

All of the following statements are correct except A) The intensity of an internal force over a sectioned area is referred to as stress. B Shear stress arises whenever the applied loads cause one section of a body to slide past its adjacent section. If a prismatic bar is subjected to an axial force acting through the centroid of the cross-sectional area, the stress is averaged over the entire cross-section. D A material exhibits elastic behavior if deformation remains even after removal of force applied.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
At a point in a piece of elastic material there are three mutually perpendicular planes on which the stresses are are follows: tensile stress 50 N/mm2 and shear stress 40 N/mm2 on one plane, compressive stress 35 N/mm² and complementary shear stress on the third plane. Find : (a) the principal stresses and the positions of the planes on which they act, (b) the positions of the planes on which there is no normal stress.
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
A symmetrical framework consisting of three pin-connected bars is loaded by a forceP (see figure). The angle between the inclined bars and the horizontal is a = 52°. Theaxial strain in the middle bar is measured as 0.036.Determine the tensile stress in the outer bars if they are constructed of a copper alloyhaving the following stress-strain relationship:
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
7. A steel rod of diameter 10 mm carries an axial load of 10 kN. Consider the modulus of elasticity and Poisson's ratio of 20 GPa and 0.30 respectively. Calculate: a) the normal stress in the rod. b) the lateral strain in the rod. c) the change in diameter of the rod when the load is applied
A steel rod with a cross-sectional area of 0.25in2 is stretched between two fixed points. The tensile force in the rod at 70°F is 1200lb. If a = 6.5x10-6/°F and E = 29x106 psi, What will be the stress at 0°F? At what temperature will the stress be zero? A bronze bar 3m long with a cross-sectional area of 320mm2 is placed between two rigid walls. At ta temperature of -20°c, the gap A = 25mm. Find the temperature at which the compressive stress of the bar will be 35 MPa. Use a = 18x10-6 m/ (m. °C) and E = 80GPA.