All of the following tubes are of equal length. The pressure at each end of the tubes are indicated above the tubes. The radius of tubes A and Care 1 cm. The radius of tubes B and D are 2 cm. Rank the tubes from the one that would have highest (1) left-to-right flow to the lowest 125 mm Hg 100 mm Hg A 75 mm Hg 25 mm Hg B 75 mm Hg 25 mm Hg

All of the following tubes are of equal length. The pressure at each end of the tubes are indicated above the tubes. The radius of tubes A and Care 1 cm. The radius of tubes B and D are 2 cm. Rank the tubes from the one that would have highest (1) left-to-right flow to the lowest 125 mm Hg 100 mm Hg A 75 mm Hg 25 mm Hg B 75 mm Hg 25 mm Hg

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter9: The Gaseous State

Section: Chapter Questions

Problem 19P

See similar textbooks

Similar questions

High-pressure liquid chromatography (HPLC) is a method used in chemistry and biochemistry to purify chemical substances. The pressures used in this procedure range from around 500 kilopascals (500,000 PaPa) to about 60,000 kPakPa (60,000,000 PaPa). It is often convenient to know the pressure in torr. If an HPLC procedure is running at a pressure of 5.50×108 Pa, what is its running pressure in torr? Express the pressure numerically in torr.
An airbag arises from the bottom of a well where the temperature is 35 °C, to the surface where the temperature is 29 °C find the percent increase in the volume of the bubble if the depth of the well is 6 cm. Atmospheric pressure is 10 101528 Pa
At 27 °C, 500 cc of H2, measured under a pressure 400 torr, and 1000 cc of N2, measured under a pressure of 600 mm Hg, are introduced into an evacuated 2-L flask. Calculate the resulting pressure. (Given -> Unknown -> Solution -> Answer)
ITEMS USED FOR EXPERIMENT: •Ring stand •Hot plate •125 mL Erlenmeyer flask•400 mL beaker•10 mL graduated cylinder •Aluminum foil•Rubberband•Paper Clip•Thermometer•Vial containing unknown liquid You know have the following data: Mass of flask + foil + rubberband: 78.637 gMass of flask + foil and rubberband+ unknown condensed liquid: 78.847 gTemperature of water bath: 100C = 373 KPressure of gas in our system: 29.02 inHg = 0.9699 atmVolume of gas in our system: 141 mL = 0.141 L 1. During the experiment, you collect the following data: Mass of flask: 80.001 g Mass of flask + unknown condensed liquid: 80.452 g Temperature of water bath: 100 °C Pressure of gas in our system: 0.998 atm Volume of gas in our system: 265 mL Which of the following number(s) need a conversion before they can be used? (Check all that apply) [ ] Group of answer choices [ ] Volume of gas in our system [ ] Mass of flask [ ] Temperature of water bath [ ] Pressure of gas in our system [ ] Mass of flask +…
1.) A gas at 250 K and 1520 kPa has a molar volume 12% smaller than that calculated from theperfect gas law. Calculate (a) the compression factor under these conditions, and (b) the molarvolume of the gas. Answer: [0.88; 1.20] 2.) At 300 K and 2026 kPa, the compressibility factor of a gas is 0.86. Calculate the volume occupied by 8.2 mmol of the gas under these conditions. Answer: [8.68 x 10^-3]
a ballon is filled to a volume of 1.50 L with 3.00 moles of gas at 25c with pressure and temperature held constant ,what will be the volume of the ballon if 0.90 molds of gas are added?
Tooling for a vacuum deposition system is cleaned and reassembled. Unfortunately, a drop of water 0.125 cm3 in volume is left in the bottom of a screw hole. Due to the obstructed path to the pump, a negligible amount of water escapes during the early stages of pumpdown, and the drop becomes a virtual leak at a chamber pressure of 4.3E-06 torr. Find the volume of gas formed by the water at this pressure (assume it stays at room temperature). The density of water is 1g cm-3 and the molecular weight 18 g mole-1. (First, determine the number of moles in the drop of water, and use the ideal gas law to determine the volume)(b) To make this result clearer, what is the added time (in hours) to pump out this chamber due to this droplet if the pump, at that pressure, has a rate of 1480 L/s?
Consider Figure 13.1. If the height of the mercury column in the leveling bulb is 21 mm greater than that in the gas buret and atmospheric pressure is 600 mm , what is the pressure on the gas trapped in the buret? Should I assume (1 atm) or would I assume the atm is 600mm (standard) and subtract the 21 from the 600, then convert by division (600-21)/760 ?? thanks
Perform the following pressure conversions, assuming when necessary that atmospheric pressure is 1 atm. Unless otherwise stated, the given pressures are absolute. (a) 2600 mm Hg to psi(b) 275 ft H 2O to kPa(c) 3.00 atm to N/cm2(d) 280 cm Hg to dyne/m2(e) 20 cm Hg of vacuum to atm (absolute)(f) 25.0 psig to mm Hg (gauge)(g) 25.0 psig to mm Hg (absolute)(h) 325 mm Hg to mm Hg gauge(i) 45.0 psi to cm of carbon tetrachloride
High-pressure liquid chromatography (HPLC) is a method used in chemistry and biochemistry to purify chemical substances. The pressures used in this procedure range from around 500 kilopascals (500,000 Pa) to about 60,000 kPa (60,000,000 Pa). It is often convenient to know the pressure in torr. If an HPLC procedure is running at a pressure of 1.70×108 Pa, what is its running pressure in torr?Express the pressure numerically in torr.
An 8.0L tank at 29*C is filled with 16.6g carbon monoxide gas and 6.5g of sulfur hexafluoride gas. You can assume both gases behave ad ideal gases under these conditions. Calculate the mold fraction of each gas. Round your answer to 3 significant digits.
An open-end mercury manometer is to be used to measure the pressure in an apparatus containing a vapor that reacts with mercury. A 10-cm layer of silicon oil (SG = 0:92) is placed on top of the mercury in the arm attached to the apparatus. Atmospheric pressure is 765 mm Hg.(a) If the level of mercury in the open end is 365 mm below the mercury level in the other arm, what is the pressure (mm Hg) in the apparatus?(b) When the instrumentation specialist was deciding on a liquid to put in the manometer, she listed several properties the fluid should have and eventually selected silicon oil. What might the listed properties have been?