i need the answer quickly Determinethemaximumpermissible angle between theshaft axes of a universal jointif the driving shaft rotatesat 800 rpm and the total fluctuation of speeddoes not exceed 60 rpm. Also, find the maximumand the minimum speeds of the driven shaft.

Answered: Image /qna-images/answer/2e58fd36-e3b8-4a18-ab54-15760dab09cc.jpg

Answered: Also, ISO, nna the maxmu

Engineering

Mechanical Engineering

Also, ISO, nna the maxmu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axis are 30o. Produce a graph of velocity ratio against angle for f to proof the calculated results.
An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 200 kg at the crank pin, and the reciprocating masses per cylinder to 300 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the value of variation in tractive effort at 300 rpm. Select one: A. ±58476 N B. ±69780 N C. ±79654 N D. ±12475 N
The equation of the turning moment diagram for the three crank engine is given by:where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
Hook's joint is used to couple two shafts together. The driving shaft rotates at uniform speed of 1000 rpm. Determine the greatest permissible angle between the shaft axes so that the total fluctuation of speed of the driven shaft does not exceed 150 rpm. What will be the maximum speed of the driven shaft?
Shaft "a" in the figure rotates at 450 rev/min in the direction shown. Find the speed and direction of rotation of shaft "d".
A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72-tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive: a. The velocity ratiob. The angular velocity of the output shaftc. The linear belt speedd. The belt wrap on the input and output sprocketse. The belt perimeter lengthf. Draw the schematic of the belt drive system
A horizontal cross compound steam engine develops 500 kW at 100 rpm. The coefficient of fluctuation of energy as found from the turning moment diagram is to be 0.1 and the fluctuation of speed is to be kept within ± 0.5% of the mean speed. Find the mass of the flywheel required, if the radius of gyration is 3 meters.
The driving shaft of a double Hooke's joint rotates at 200 rpm. The angle of the driving and of the driven shaft with the intermediate shaft is 15° If the forks of the intermediate shaft lie in planes perpendicular to each other, determine the maximum and the minimum velocities of the driven shaft.
A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. Themaximum belt tension is not to exceed 620 N and it is required to transmit 1·8 kW at anoutput speed of 360 rev/min. Determine:(a) The input torque. (b) The belt speed. (c) The limiting slack side tension. (d) The initial tension at which the belt should be set.
The equation of the turning moment diagram for the three crank engine is given by: T(N.m) =25000 - 7500 sin 3theta where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
Power is transmitted between two pulleys mounted on the parallel shafts rotating in the opposite direction. The pulleys are separated apart at a distance of 1950mm having 0.45m and 0.2m diameter respectively. What power can be transmitted by the belt when the larger pulley rotates at 200 rev/min, if the maximum permissible tension on the tight side of the belt is 1000 N, and the value of µ between the belt and pulley is 0.25. Design the length of the belt required and the angle of contact between the belt and each pulley.
The torque of the screw jack is 100 N-m and its speed is 30 rpm. Evaluate power of the device