9An a-c source deliver current to two lo nds A end B that are con-nected in parallel. If the load A current is 25 amp lo eds the B-load current of 42.2 amp by 45 eloc deg, (a) calculato the resul-.tant curren t and (b) deterninc the anclo boctwoen the rcsultrntcurrent and -an assuned A-current rofurence.Ans. (a) 62.6 cmp (b) 28.5 lng

In this question we need to find a resultant current and angle .

An a-c source delivor current to two lo ads À end B that cro con- nected in parallel. If the load A current is 25 amp lo eds the B- load current of 42.2 amp by 45`elcc deg, (a) calculato the resul- .tant curren t̟ and (b) deterninc the an lo betwocn the rcsultrnt current and -an assunIed A-currcnt rofurenco. Ans. (a) 62.6 mp (b) 28.5*lag

An a-c source delivor current to two lo ads À end B that cro con- nected in parallel. If the load A current is 25 amp lo eds the B- load current of 42.2 amp by 45`elcc deg, (a) calculato the resul- .tant curren t̟ and (b) deterninc the an lo betwocn the rcsultrnt current and -an assunIed A-currcnt rofurenco. Ans. (a) 62.6 mp (b) 28.5*lag

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the output waveform for the comparator circuit in figure below. Assume that Q? +Vout(max) = +10 V and Vout(max) = -10V. Vin U1 Vout R1 +3 V 80ko 0- R2 20ko Con'l
Q/ Why is high frequency (Fsw ) used in Buck Converter circuits
) Design a Comparator Circuit that have V¢ = +8V -Vcc=-8V, V reference = 4 V at non-inverting terminal Vinput = Sine Wave 20 Vp-p at inverting terminal.
circuit diagram of AC to DC using ltspice show Vin and Vout
Figure shows a transistor switching circuit. Find the Vcc and Rc, which causes the output voltage to have a peak to peak value of 6V (given that the input voltage signal Vi, and the output voltage signal Vo, have units of Volt) Fone: V₁ 10k2 www +Vcc Rc V₂ B-100
noninverting op- anp. Av=15 and findl io & vo în terms of resistenas B1 Design THio R3 Vi
17. If a signal voltage of 10 mV rms is applied to each amplifier in Figure 12–66, what are the out- put voltages and what is their phase relationship with inputs? 1.0 MO R 47 k
Determine VE = HON Vin RE62092 R₂ 10ΚΩ BDC=200 R₁ VB = Rc1.2kQ 22kQ Vout -OVcc=+24V and Vc = for the circuit.
Q) Figure below amplifier .given the input wave FOrm Shows a Comperator Circuit Vs using 6 sin wt Volt. the output OPerational Sketch and label the input Voltage Vs and wave Forms Voi and Vo1 12 V tov -10V Vs - lov Vos -tov
Qhe Three resistors are corinectedl in series to a (220 V)suppl The combined voltage drop across (Ri) and (R2) is (140 V) that across CRe) and CB) is (180 V). Il the total res istance is (sdkn), calcuate CRi, Rev and Ra) ara
A Draco the amos Circuit and layout for the following funetions ond implerment the layouts on the Microwind Simulation. F = A+B F = AB F= A+ Btc F = A.B.C AB + C AB.C F = XY+ WZ
A2 Consider the circuit in Figure A2 where Vs = 12 V, R₁ R₂ and the input is a sinusoidal signal with peak voltage of 35 mV. Draw a plot of the signal against time that you expect to measure at the output and explain how the circuit functions. +Vs R₁ R₂ Vout Vret Hi Vin + Ao -Vs Figure A2