Answered: When connected to a 120 V (rms). 60 Hz…

When connected to a 120 V (rms). 60 Hz power line, a load absorbs 4 kW at a lagging power factor of 0.8. Find the value of capacitance necessary to raise the power factor to 0.95

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Related questions

Q: The effective value of the sinusoidal voltage across a certain network is 32 V rms and the peak…

A: Given data, Ip = 24 mA. Vrms = 32 V. P = 0.48 W.

Q: Consider an electric motor that requires a 120 V rms power source and a current of 1.5 A rms. If the…

A: Given an electric motor that requires a, Source voltage, Vrms=120 V Current, Irms=1.5 A The…

Q: A 250 V rms system is supplying three parallel loads. One draw 20kW at unity pf, a second uses 25…

A: The complex power in an AC system is defined as the product of rms value of applied voltage and…

Q: An alternator is supplying a load of 300 kW at a p.f. of 0.6 lagging. If the p.f. is raised to…

A: Given, An alternator is supplying a load of, P1 = 300 kW At power factor, cosϕ1=0.6 lagging Raised…

Q: if a Load absorbs an average power of 8 kW at a leading power factor of 0.5 Select one: O a. -8000 -…

A: The total power that flows is called the apparent power. This power is complex in nature. This power…

Q: Find the power factor at the source and vs(t) if f = 60 Hz. What value of inductance must be placed…

A: It is required to calculate the value of the inductance for which the supply power factor will…

Q: Determine the average power delivered to the circuit consisting of an impedance Z = 5+j8 N when the…

Q: An industrial heater has a nameplate that reads: 200 V, 60 Hz, 12 kVA, o.788 pf lagging Determine…

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: When connected to a 120-V (rms), 60-Hz power line, a load absorbs 4 kW at a lagging power factor of…

A: Given values are -

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given, Active power, P = 300 kW Power factor, cosϕ=0.6 lagging When the power factor is raised to…

Q: Q/ when connected to a 120V (rms), 60HZ power line , a load absorbs 4Kw at a lagging power factor of…

Q: When connected to a 120V (rms), 60Hz power line, a load absorbs 4kW at a lagging power factor of…

A: Power factor: It is a working or real power, measured in kilowatts divided by the apparent power,…

Q: Example 1: Calculate the RMS and the available power at the thermal noise in 100 2 at 27 C° and 6M.…

A: Given data, Resustance is given R=100 Ω Temperature is given as, T=270 C=273+27=300 K Bandwidth B=6…

Q: Find the resultant of the two out of phase current If the component currents are 12 and 16 amp.,…

Q: A load operates at a voltage of Vx = 475 V−rms and absorbs P = 56 and Q = 23 VAR of power. Use this…

Q: 10.2 Calculate the average power absorbed by the resistor and inductor. Find the average power…

Q: A load absorbs 72044 W at a lagging power factor of pf = 0.67. If the current flowing through the…

A: Given: Power, P=72044W power factor, pf=0.67 Current, Ix=0.100 A−rms

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: Power factor is defined as the ratio of active power to apparent power. It gives an idea about how…

Q: A V sine The supply voltage V = 120230° volt. Load A is 4 KVA at power factor 0.8 leading. Load C is…

Q: Q10. If the impedance of a circuit = 20 – j10 1. if a voltage source is connected across this…

A: Given: Impedance Z=20-j10Ω Voltage source is connected across impedance.

Q: Circuit Diagram V1 R1 220 Vrms MA 150 Ω 60 Hz 0.⁰ L1 100mH Computed Values Compute the expected…

A: Power factor is the measure of how effectively the incoming power is used in an electrical system. A…

Q: The power factor of a circuit is 0.5 lagging. The power delivered in watts is 500. If the input…

Q: A 50 Hz sinusoidal AC voltage source of peak value V, = 340 V delivers power to a resistive load of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: If a supply voltage is represented as "single phase, 200 V, 50 Hz" the 200 V is the RMS valu of…

Q: A load operating at 280 V RMS draws 81 A RMS at a power factor 0.97 leading. Find: 1. The real power…

A: Given, Vrms=280 VIrms=81 ACosϕ=0.97 leading

Q: Circuit Diagram V1 R1 220 Vrms >5002 60 Hz 0.⁰ L1 100mH Computed Values Compute the expected power…

A: Note:- As connection of capacitor is not given whether it is series or parallel. I solved it by…

Q: A current of 2.5 A through a neon light advertisement is supplied by a 115 V RMS voltage source. The…

A: Given data: I=2.5 AVrms=115 V The expression for the rms value of current is given as, Irms=2.52 A…

Q: -j25 9 /25 N j20 N (+

Q: Circuit Diagram V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Given: You have a complex inductive load that is dropping 240 VRMS. The operating frequency is 60…

Q: 40 mH (15.1 2) am 120 uF 120 LO Rms 10 2 (-j22.1 Q)

A: Steps to find the power in the complex circuit, Find the equivalent impedance of the circuit Then…

Q: i(f) A Answers: 2.31 A, 10.67 W 0 1 2 3 4 5 6 t

A: The solution is given below

Q: Example 1: Calculate the RMS and the available power at the thermal noise in 100 2 at 27 C° and 6MH:…

A: It is given that: R=100ΩT=27°CB=6MHz

Q: A0) is supplied by an RMS value of 22o-v, 60-Hz source

Q: In an AC circuit, the power factor is the factor by which the apparent power is multiplied to obtain…

A: We need to tell the result of the multiplication of apparent power and power factor. Reactive power…

Q: An industrial process requires a power of 10 kW with a lagging power factor of 0.6 in a single-phase…

Q: Calculate: Reactive, apparent and active power of the circuit, consider the power supply 120V rms…

Q: What is the value of real power supplied by the source in the figure? 60 ww 30/0° V rms -j20 42

A: Equivalent impedance can be obtained by,…

Q: RE VR v, = Vm sin(m1) L + *I +

A: Given data The rms voltage is Vrms = 140 V Frequency is f = 50 Hz Resistance is R = 100 ohm…

Q: An AC source of RMS voltage 20 V with internal impedance Z, = (1+2j) Q feeds a load of impedance Z,…

A: Given circuit is -

Q: For the circuit with source V1 shown below, determine the average power supplied by V1 v1(t) = 15…

A: Circuit is given as,

Q: Example: Find the rms value for the current waveform shown below: 1 1 3 4 6 t(sec)

A: RMS Value of a signal: It's that steady state equivalent of a time varying signal which would…

Q: Two units, connected in parallel, are energized by an a-c source. If the component currents are 15…

Q: Circuit Diagram Computed Values Compute the expected power factor of the circuit given the different…

A: Power factor: It tells how much active power is utilized by the circuit from the apparent power.…

Q: Example 1: Calculate the RMS and the available power at the thermal noise in 100 2 at 27 C° and 6MH…

A: We need to find RMS voltage and power for given details

Q: Which of the following AC power parameters is the closest equivalent to the DC power drawn by the…

A: ac power parameters is closest equivalent to the dc power drawn by the circuit=?

Q: A 240-V rms 60-Hz supply serves a load that is 10 kW (resistive), 15 kVAR (capacitive), and 22 kVAR…

A: The power factor of a circuit can be obtained as cos∅=PP2+Q2…

Q: 9.71 Determine the power factor of the entire circuit shown below seen by the source. Calculate the…

A: Given circuit,

Q: А сарасtoг 00 ohms. The combination is further connected in series with an inductance of O5 mH and…

A: A capacitor having C=3.18 mF which is connected in parallel with the Resistance of Resistance…

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

When connected to a 120 V (rms). 60 Hz power line, a load absorbs 4 kW at a lagging power factor of 0.8. Find the value of capacitance necessary to raise the power factor to 0.95

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
A load with a voltage amplitude of 50 Hz 300 V rms at its terminals consumes 28.98 kW at a back power factor of 0.69. If a 225.87 microfarad capacitor is connected parallel to the terminals of this load, how much will the amplitude of the current drawn from the line decrease?
When connected to a 120 V (rms), 60-Hz power line, a load absorbs 4kW at a lagging power factor of 0.8. Find the value of Capacitance, C, necessary to raise the power factor to 0.95 lagging.
An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is raised to unity, how many more kW can alternator supply ?
A load operates at a voltage of Vx = 475 V−rms and absorbs P = 56 and Q = 23 VAR of power. Use this information to calculate the apparent power (S) and the power factor (pf) for the load. THank you for the help
An alternating voltage given by v = 120 sin (240t + п / 4) V, is applied to a coil withnegligible resistance and inductance of 100 mH. Determine (a) the reactance of thecoil, and (b) the RMS current flowing through the circuit.
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by pi/3 radians and the line current is 23.4 amp, determine the current in B.
An industrial process requires a power of 10 kW with a lagging power factor of 0.6 in a single-phase system. It is desired to add a parallel capacitance to raise the power factor to unity. For a line voltage of 240 V rms, determine the value of capacitance required.
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total line current is 23.4 amp. (rms), determine the current in B.
A load absorbs 72044 W at a lagging power factor of pf = 0.67. If the current flowing through the load is Ix = 0.100 A−rms, determine the impedance of the load.
A voltage given by v(t) = 311 cos (311 pi t) V is applied to a 50-ohm resistance. (a.) Sketch v(t) to scale versus time. (b.) Determine the rms value of the voltage and the average power delivered to the resistance. (c.)Determine the power as a function of time and sketch to scale.