An anion has an electrophoretic mobility of -2.50 cm2 /kV - min on a CE system containing a 30 cm long capillary with a detector located 25.0 cm from the point of injection. If the electroosmotic mobility of the buffer is 4.10 cm- /kV - min, and the applied voltage is 15.0 kV, what are the migration time (v) and the apparent mobility (Ha)?

An anion has an electrophoretic mobility of -2.50 cm2 /kV - min on a CE system containing a 30 cm long capillary with a detector located 25.0 cm from the point of injection. If the electroosmotic mobility of the buffer is 4.10 cm- /kV - min, and the applied voltage is 15.0 kV, what are the migration time (v) and the apparent mobility (Ha)?

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter25: Voltammetry

Section: Chapter Questions

Problem 25.12QAP

See similar textbooks

Similar questions

Calculate the gravimetric factor of the following. 2 Fe is sought(Analyte), 1Fe2O3 is weighed (Precipitate)
A 0.2g sample of toothpaste containing fluoride was treated with 50 cm3 of a suitable buffer solution and diluted to 100 cm3. Using a fluoride ion-selective electrode, a 25.00 cm3 aliquot of this solution gave cell potentials of –155.3 mV before and –176.2 mV after spiking with 0.1 cm3 of a 0.5 mg/cm3 fluoride standard. Calculate the pF– corresponding to each cell potential and the percentage by weight of fluoride in the toothpaste.
Which is not an error associated with an incorrectly defined pH measurement? A) contact potential deviation-AgCl or Ag precipitates due to dilution of KCl or presence of reducing reagentB) alkaline fault - electrode responds to Na+ instead of H+ when [Na+] is low and [H+] is highC) acid error – the measured pH is higher than the actual pH because the glass is saturated with H+ and can no longer be protonatedD) temperature – the pH meter is calibrated at different temperatures from the sample
The amount of iron in a meteorite was determined by a redox titration using KMnO4 as the titrant. A 0.4185 -g sample was dissolved in acid and the liberated Fe3+ quantitatively reduced to Fe2+, using a reductor column. Titrating with 0.0044 M KMnO4 requires 28.76 mL to reach the end point. Determine the %w/w Fe2O3 in the sample of meteorite. (Fe = 55.845 amu, Fe2O3 = 159.69 g/mol
In an experiment to determine the concentration of H2SO4 in a brand of toilet cleanser, 10.0 cm3 of the cleanser was first diluted to 250.0 cm3 with distilled water. 25.0 cm3 of the diluted cleanser were titrated with 0.320 mol dm–3 NaOH solution, using methyl orange as indicator.If 29.2 cm3 of NaOH solution is used, what is the concentration of H2SO4 in the undiluted toilet cleanser?a. 2.30 mol dm–3b. 4.60 mol dm–3 c. 9.20 mol dm–3 d. 11.50 mol dm–3
The concentration of ammonia in a cleaning product was determined by back titration.Firstly, 10.00 cm3 of the cleaning product was pipetted into a large conical flask,containing 250.00cm3 of 0.50 mol/l HCl to give Solution A.Following a period of reaction and shaking, 50.00cm3 of Solution A was removed anddiluted to 250 cm3 with water in a volumetric flask to give Solution B.20 cm3 samples of Solution B were titrated against 0.05 mol/l Na2CO3 solution, givingan average titre of 12.45 cm3. i) Write equations for the reactions that have taken place.ii) Determine the concentration of NH3 in the original cleaning product in mol/l,g/l, ppm, and % w/v.
A 20.0 mL sample of commercial bleach was diluted with water to a 250.0 mL volumetric flask. A 50.0 mL aliquot of the diluted sample was treated with excess KI and starch. The liberated iodine was titrated with 0.399 M Na2S2O3, requiring 13.9 mL to reach the end point. (a) Identify the type of redox titration method used. (b) Identify the indicator and endpoint color. (c) Calculate the % w/v NaOCl in the sample.
Five white, 500-mg uncoated ascorbic acid (AA) tablets with an average weight of 0.6100-g were pulverized in a mortar. A sample of the powdered ascorbic acid weighing 0.4610-g was placed in an iodine flask and was dissolved in 50-mL H2SO4 then 5-g of KBr was added to the resulting solution. The solution was titrated with 46.73-mL of 0.0152 M STD. KBrO3 to reach a faint yellow endpoint then 3-g KI and 5-mL Starch TS. The blue color solution is then titrated with 2.78-mL of 0.1047 M STD. Na2S2O3 to reach the disappearance of the blue iodostarch complex. MW: KBrO3 = 167.0 ; KIO3 = 214.0 ; Na2S2O3 = 158.11 ; C6H8O6 = 176.12 Compute the milligrams of pure AA per tablet from the assay. None of the choices 349.7 mg 264.3 mg 462.7 mg
A 0.6025 g sample was dissolved and the Ca2+ and Ba2+ ions present were precipitated as BaC2O4.H2O and CaC2O4.H2O. The oxalates were then heated in a thermogravimetric apparatus leaving a residue that weighed 0.5713 g in the range 320oC to 400oC and 0.4674 g in the range 580oC to 620oC. Calculate the percentage Ba in the sample.
A pH probe/meter uses the following equations: Ecell = L + 0.0592 log a1 = L - 0.0592 pH Where L = L1 + EAg/AgCI + Easy= constants L1 = - 0.0592 log a2 a1 = activity of analyte solution a2 = activity of internal solution Questions: How will measured pH value be affected vs “real” pH if the temperature of the sample is 30C when pH was measured? How will measured pH value be affected vs “real” pH if HCl in pH electrode, became 0.15M instead of 0.1M? How pH value will be affected vs “real” pH if the glass of the pH electrode is not fully hydrated? Please answer all questions and provide a brief explanation
For titration for determination of Chloride, 0.05 AgNO3 and NaCl with a 5% (w/v) K2CrO4 indicator, what is the % (w/w) Cl- using the atomic weight for Chlorine. Data below: Primary standard weight 0.1173g , 0.1056g , and 0.1049g Vol of titrant delivered 35.47mL , 31.75mL, and 31.04mL Uknown Chloride mass 0.1527g, 0.1442g, and 0.1337g Vol of titrant delivered 40.00mL ,37.68mL ,and 34.96 mL
1) Name the applications of glass electrodes in potentiometric measurements (please write correctly and concisely).