An axial load P is applied to the rectangular bar shown. The cross-sectional area of the bar is 565 mm2. Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB if the bar is subjected to an axial load of P = 59 kN. Assume a = 33°. P A a Answers: The normal stress o = i MPa. The shear stress 7 =

An axial load P is applied to the rectangular bar shown. The cross-sectional area of the bar is 565 mm2. Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB if the bar is subjected to an axial load of P = 59 kN. Assume a = 33°. P A a Answers: The normal stress o = i MPa. The shear stress 7 =

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

The normal and shear stresses on a plane are 120 psi (C) and 25 psi respectively. On an orthogonal plane, the respective stresses are 40 psi (C) and 25 psi. Draw Mohr's circle and determine the angle between minor principal plane makes with the 120 psi stresses.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure. Unbiased Determine the position of the axis and draw the stress distribution in the section
Find the expressions to calculate the maximum normal and shear stresses for a circular profile: d (diameter)= 0.30 m
Determine the shear stress at points A, B, C andD for the following section. Also determine the maximum shear stress, then plot the shear stress distribution. Given: V = 10 kN.
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
For the beam in the question above, determine the maximum shear stress. sketch thesection stress distribution.
P = 49 kips Determine the normal and shearing stress at point a, b, and c
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.