Please use the Mohrs circle to solve this For the plane stress state shown below, calculate the major principal stress g,and the minorprincipal stress đg, and the angle of rotation to obtain these principal stresses [Use MohrCircle to solve Q9].oy-1 kPaTx=1 kPaTxy=1 kPa0,=2kPa0,=2kPao-1 kPa

Steps to draw Mohr circle : 1- Select origin O and axis passing through O represents σ (x-axis) and…

For the plane stress state shown below, calculate the major principal stress gand the minor principal stress og, and the angle of rotation to obtain these principal stresses [Use Mohr Circle to solve Q9].

For the plane stress state shown below, calculate the major principal stress gand the minor principal stress og, and the angle of rotation to obtain these principal stresses [Use Mohr Circle to solve Q9].

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Related questions

Q: ,7 For the following soil element at a depth of 20 m, find: (a) The principal stresses, assuming the…

A: Normal Stress: It is defined as the stress which is induced due to the application of axial force on…

Q: Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2).…

A: Applying Boussinesq's Equation: ∆σz=3P2πz21+rz25/2 ...(1)

Q: 9. 50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the ground…

Q: Compute the vertical stress increments under Points A, B,

Q: 1. Fill in the blanks; (a) Theoretically, the vertical stress at surface under a point load is (b)…

Q: a. For the soil element shown in the figure, the magnitudes of the stresses are kN kN Oz = 70 kN Oy…

Q: Problem 1 200 MPа Use Mohr's circle to find (1) The principal stresses (2) Sketch the stress element…

A: We have to determine principal stress maximum in-plane shear stress and if rotate to AB plane than…

Q: 24.01 Stresses in a Soil Mass For the state of stress as shown, determine the inclination of minor…

A: Draw the Mohr's circle corresponding to the given state of stress. The angle required can then be…

Q: refer to the figure due to application of line load q1 and q2 . the vertical stress increase at…

A: Given: The vertical stress is 42 kN/m2. Consider the figure,

Q: Find the shear flow distribution in the rectangular thin-walled section shown. Hence, find the…

A: using basic shear flow expression…

Q: 105 КРа 30 КРа В 430 КРа 52° 75 КРа A

Q: Using the principles of Mohr’s circles for the soil element shown in Figure 10.36, determine the…

A: The angle is the rotation stress equation is determine the actual maximum and minimum stress points.…

Q: Q#3. An earth embankment diagram is shown in Figure.1. Determine the vertical stress increase at A…

A: The embankment with sloping side show the trapezoidal load. It is necessary to calculate the…

Q: Q.1 The state of stress at a point in a soil mass is given below, Determine the principal stresses…

A: When normal vectors of a plane are making same angle with the principle stresses then that plane is…

Q: 10-16. A 1 m cube within a mass of stressed soil has a stress of 100 kPa on its top and bottom…

A: since the given question is having multi sub parts therefore as per guidelines only 1-3 subparts…

Q: 2. (10 pts) Refer to Figure 1. Due to application of line load q₁, the vertical stress increase at…

Q: 2 Refer to Figure 10.42. A strip load of q= 43 kN/m? is applied over a width, B= 11 m. Determine the…

Q: Using the graphical method (Mohr’s circle), find the normal and shear stresses on plane AB from the…

A: Given: The stresses are, σ1=172 kPaσ3=145 kPa The angle is 62o. Consider the figure,

Q: 120 kPå 30kPa A 30KPA 40° 150 kPa

A: plane which has zero shear stress is called principle plane . the normal stress occurring in these…

Q: (a) Draw the Mohr circle that describes the 2D stress state and find the maximum shear stress that…

Q: A B C D P1 P2 0.60 m 1.20 m 0.90 m

A: Solution Given Data A=400 mm2P1=20 kNP2= 50 kN

Q: The principal stress orientation and maximum in-plane stress orientation are allways from each…

A: ans: option (d) is correct 45 degree offset 90 degree offset

Q: 10 ft Point loads of magnitude 2000, 4000, and 6000 lb act at A, B, and C, respectively as shown on…

A: Given: The point load at A is 2000 lb. The point load at B is 4000 lb. The point load at C is 6000…

Q: Q5) If the applied shear force V 90 kN, Plot the intensity of the shear-stress distribution acting…

Q: Q1: Find the increase in stress in (mPa) at soil element (A) due to the application of the external…

A: Given data: Load=730 kN, 2420 kN Depth=1m It is asked to calculate the stress at soil element A…

Q: Explain about the Taylor slope stability curves for total stress analysis.

A: The measurement of total stress utilizes the soil's undrained shear strength. Normally, the complete…

Q: Determine the shear stress at points A, B, C andD for the following section. Also determine the…

A: Given V=10kN Determine the shear stress at points A, B, C andD for the following section.

Q: soil element is shown in Figure. Determine the following a. Maximum and minimum principal stresses…

Q: 100 kN point load and 40 kN/m line load are applied on the ground surface as shown. Compute the…

Q: 7. For the soil element shown, determine the following: a. Maximum and minimum principal stresses b.…

Q: PROBLEM 2 (15 points): The magnitude of stresses of the soil element represented by the figure below…

Q: Problem 2: A soil element is shown 5.4 kN/m2 in the figure on the right. The magnitude of stresses…

A: Answer:- It can solve by the help of formula for major and minor principal stresses.…

Q: Q # 3. State the following Failure Theories; Also write their specific equations for Failure…

A: *THEORY OF FAILURE:- Under uniaxial loading circumstance prediction of failure may be very smooth…

Q: Determine the vertical stress increase, Aoz, at point A with the following values: q1 = 90 KN/m; q2…

A: Given: Line loads Vertical distance Radial distance To find: Vertical stress increase at point A to…

Q: Problem (4.8): A 90-N.m torque is applied to a hollow shaft having the cross section shown in Figure…

Q: The cross-sectional area shown is subjected toV-600 kN and M-1000 kN-m. What is the transverse shear…

Q: 1. Suppose that the forces acting to the faces are distributed uniformly. Then find the thickness &…

Q: in circular pipe flow, shear be included). Explain the dynamic equilibrium stress profile (diagrams…

A: The shear stress in laminar flow is a direct result of momentum transfer among the randomly moving…

Q: Refer to Figure, q1 = 90 kN/m; q2 %3D 325 kN/m; x1 = 4 m; x2 = 2.5 m; z = 3 m. the vertical stress…

Q: A newtonian fluid flows down an infinitely long cyalindrical tube (as shown in the figure below).…

A: Solution;

Q: Q2 (a) Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m² due to…

A: Figure is as shown

Q: (c). The magnitude of stresses have been applied on soil element where Normal vertical stress is 120…

A: Normal stresses are given and we have to find the stresses on the inclined plane given in question…

Q: An earth embankment is shown in the figure. Determine the stress increase at point B due to the…

A: Consider the given diagram.

Q: The soil element is shown in the figure. Using the pole method, drtermine: a) Major and minor…

A: From the given stress element, σx=-17 kN/m2σy=-26 kN/m2τxy=8 kN/m2

Q: 1. The Griffith criterion is seen to have a steeper slope at high confining pressures 2. In a Mohr…

A: 1. It is often observed that the Griffith criterion may give a reasonably good description of…

Q: CEN-333 Geotechnical

A: Boussinqi's equation: σZ=QZr32π11+rZ252where,Z=Depth of the pointQ=point load actingr=radial…

Q: The vertical stress at point P1 due to the point load Q on the ground surface as shown in figure is…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

100%

Please use the Mohrs circle to solve this

For the plane stress state shown below, calculate the major principal stress g,and the minor
principal stress đg, and the angle of rotation to obtain these principal stresses [Use Mohr
Circle to solve Q9].
oy-1 kPa
Tx=1 kPa
Txy=1 kPa
0,=2kPa
0,=2kPa
o-1 kPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
Determine the maximum of the following: Bearing Stress, Tensile stress, and Shear stress in MPa if P=115 kN Note: the figure given is provided for the three stress that is needed to solve
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 57 kN/m2. Both stresses are principle stress. (a) Draw the Mohr circle that describes the 2D stress state at the point. (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements (10 marks)
For soil elements shown in the figure, determine the maximum and minimum principal stresses. Also determine the normal and shear stresses on plane AB.
Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 13 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1).
For the beam in the question above, determine the maximum shear stress. sketch thesection stress distribution.
For the given stress element, draw the Mohr's circle and determine the principle stresses and maximum shear stress..