An electric car manufacturer is looking to utilize some stock AISI 8740, hot rolled steel bars that are around 2 inches in diameter for their conveyor system that is being set up to start producing their own batteries. The data sheet shows the the bars to have 132,000 psi tensile strength, 87,500 psi yield strength, and 16.7% elongation. A hardness of 262 Bhn allows it to be finish machined after heat treatment. They keep their workspace at 70°F. What is the working endurance strength, Se? 39,750 psi 28,562 psi 42,500 psi 33,400 psi

An electric car manufacturer is looking to utilize some stock AISI 8740, hot rolled steel bars that are around 2 inches in diameter for their conveyor system that is being set up to start producing their own batteries. The data sheet shows the the bars to have 132,000 psi tensile strength, 87,500 psi yield strength, and 16.7% elongation. A hardness of 262 Bhn allows it to be finish machined after heat treatment. They keep their workspace at 70°F. What is the working endurance strength, Se? 39,750 psi 28,562 psi 42,500 psi 33,400 psi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Suppose you need to design a tension test machine capable of testing specimens that have nominal ultimate stresses as high as σu = 100 ksi . How much force must the machine be capable of generating? Assume the testing specimen has the ASTM shape shown. Answer for this is 19.6 kip) (If the maximum nominal strain is ϵf = 0.7 just before the test specimen fractures and the test machine operates by moving only one grip, how far must that grip be designed to travel? The total length of the deforming part of the specimen is 3 in. Answer for this is 2.10 in) Do not know if this info is needed but this was the other 2 parts
Due to an applied static loading, the principal stresses at a point of a machine component are σ1 = -150 MPa and σ2 = 60 MPa. If the design of the component is to be done using a LESS conservative failure theory, then yielding will just begin if the designer chooses a ductile material with the yield strength, Sy=___. If the factor of safety needs to be at least 4 by using a MORE conservative theory, what is the minimum yield strength needed for the material?
A sheet of aluminium alloy is reduced in thickness by 25% following a rolling operation. Tensile test specimens were cut from the sheet before and after rolling. Sketch the tensile test curves for both specimens, making reference to the differences if any, in Young’s modulus, the elastic limit and the level of ductility
An application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions: Can SAE 1040 steel be selected for this application? If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected? Why is that steel with the condition in part II selected? Is the selected steel brittle or ductile? and Why?
Draw a Stress/Strain graph of a mild tensile steel and identify the limit of proportionality and the yield point
A compression test is performed on a 2” diameter by 5” long bar of an unknown metal. At the end of the compression test, the bar has a height of 3.5 inches. The strength coefficient (K) and the work hardening coefficient (n ) are 250 MPa and 0.4, respectively. State all assumptions needed to work the problem. a) Calculate the final diameter of the bar in inches. b) Calculate the flow stress in MPa when the length of the bar is 4”.
For a 10-mm-diameter Brinell hardness indenter, what will be the diameter of an indentation in mm to yield a hardness of 506 HB when a 500-kg load is used?
u have a 10-mm steel drill rod that we then heat-treated and ground. The measured hardness was found to be 290 Brinell. Estimate the endurance strength, Se, in MPa if the rod is used in rotating bending. Take the value of factor a and exponent b from Table 6–2. The endurance strength is MPa. ???????????????
A component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steelfrom which it is manufactured has an ultimate tensile strength, σu, of 1050 MPa and a measured endurancelimit, σe, of 400 MPa. The fully reversed stress at 1000 cycles is 750 MPa. Using both the Goodman and Gerbermean stress correction procedures, calculate the component life.
26c)A material has an mean indentation diameter of 3.64 mm created by a 5 mm diameter Brinell Indenter. Its hardness value is 200 HB , what will be applied force in Newtons?
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 99% reliability. Draw logarithmic S_N diagrams(A section diagram and b section diagram). (P=52 kN),(sigma(tensile)=620MPa) (reliability=%99) NOTE: RELİABİLİTY İS 99,NOT 90.PLEASE TAKE THE 99 VALUE,AND DRAW GRAPHİC A AND GRAPHİC B.
compute the tensile strength and ductility of a cylindrical copper rod if it is cold worked such that the diameter is reduced from 12 to 10 mm